当前时区为 UTC + 8 小时



发表新帖 回复这个主题  [ 2 篇帖子 ] 
作者 内容
1 楼 
 文章标题 : T43装Ubuntu7.10后,在nm-applet看不到无线网卡?
帖子发表于 : 2008-02-22 0:09 

注册: 2007-08-29 22:03
帖子: 2
送出感谢: 0 次
接收感谢: 0 次
首先,我用命令: lshw 返回结果中有以下部分显示, 是何意?
*-network UNCLAIMED
description: Network controller
product: PRO/Wireless 2200BG Network Connection
vendor: Intel Corporation
physical id: 2
bus info: pci@0000:0b:02.0
version: 05
width: 32 bits
clock: 33MHz
capabilities: pm cap_list
configuration: latency=64 maxlatency=24 mingnt=3

然后dmsg, 显示如下:
[ 0.000000] Linux version 2.6.22-14-386 (buildd@terranova) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 Tue Dec 18 07:34:24 UTC 2007 (Ubuntu 2.6.22-14.47-386)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000005fed0000 (usable)
[ 0.000000] BIOS-e820: 000000005fed0000 - 000000005fee5000 (ACPI data)
[ 0.000000] BIOS-e820: 000000005fee5000 - 000000005ff00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000005ff00000 - 0000000060000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] 638MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 392912) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 392912
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 392912
[ 0.000000] On node 0 totalpages: 392912
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 1277 pages used for memmap
[ 0.000000] HighMem zone: 162259 pages, LIFO batch:31
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F6C00 checksum 0
[ 0.000000] ACPI: RSDP 000F6C00, 0024 (r2 IBM )
[ 0.000000] ACPI: XSDT 5FED6FF2, 005C (r1 IBM TP-1Y 1270 LTP 0)
[ 0.000000] ACPI: FACP 5FED7100, 00F4 (r3 IBM TP-1Y 1270 IBM 1)
[ 0.000000] ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 000000000000102C/0 [20070126]
[ 0.000000] ACPI: DSDT 5FED72E7, DB08 (r1 IBM TP-1Y 1270 MSFT 100000E)
[ 0.000000] ACPI: FACS 5FEF6000, 0040
[ 0.000000] ACPI: SSDT 5FED72B4, 0033 (r1 IBM TP-1Y 1270 MSFT 100000E)
[ 0.000000] ACPI: ECDT 5FEE4DEF, 0052 (r1 IBM TP-1Y 1270 IBM 1)
[ 0.000000] ACPI: TCPA 5FEE4E41, 0032 (r1 IBM TP-1Y 1270 PTL 1)
[ 0.000000] ACPI: APIC 5FEE4E73, 005A (r1 IBM TP-1Y 1270 IBM 1)
[ 0.000000] ACPI: MCFG 5FEE4ECD, 003E (r1 IBM TP-1Y 1270 IBM 1)
[ 0.000000] ACPI: BOOT 5FEE4FD8, 0028 (r1 IBM TP-1Y 1270 LTP 1)
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:13 APIC version 20
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 68000000 (gap: 60000000:80000000)
[ 0.000000] Built 1 zonelists. Total pages: 389843
[ 0.000000] Kernel command line: root=UUID=a7ab6015-a926-4db3-a590-a4a2ee813f79 ro vga=791
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1862.214 MHz processor.
[ 3.278700] Console: colour dummy device 80x25
[ 3.279101] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 3.279509] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 3.330162] Memory: 1546940k/1571648k available (1929k kernel code, 23392k reserved, 877k data, 348k init, 654144k highmem)
[ 3.330181] virtual kernel memory layout:
[ 3.330182] fixmap : 0xfffa8000 - 0xfffff000 ( 348 kB)
[ 3.330183] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 3.330185] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 3.330186] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 3.330187] .init : 0xc03c0000 - 0xc0417000 ( 348 kB)
[ 3.330188] .data : 0xc02e25d5 - 0xc03bda04 ( 877 kB)
[ 3.330189] .text : 0xc0100000 - 0xc02e25d5 (1929 kB)
[ 3.330204] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 3.330265] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 3.410161] Calibrating delay using timer specific routine.. 3727.78 BogoMIPS (lpj=7455570)
[ 3.410195] Security Framework v1.0.0 initialized
[ 3.410207] SELinux: Disabled at boot.
[ 3.410216] Mount-cache hash table entries: 512
[ 3.410349] CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
[ 3.410362] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 3.410369] CPU: L2 cache: 2048K
[ 3.410372] CPU: After all inits, caps: afe9fbff 00100000 00000000 00002040 00000180 00000000 00000000
[ 3.410382] Compat vDSO mapped to ffffe000.
[ 3.410396] CPU: Intel(R) Pentium(R) M processor 1.86GHz stepping 08
[ 3.410403] Checking 'hlt' instruction... OK.
[ 3.426679] Early unpacking initramfs... done
[ 3.723432] ACPI: Core revision 20070126
[ 3.723537] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 3.740172] ENABLING IO-APIC IRQs
[ 3.740360] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 3.885442] Booting paravirtualized kernel on bare hardware
[ 3.885513] Time: 15:49:41 Date: 01/21/108
[ 3.885532] NET: Registered protocol family 16
[ 3.885598] EISA bus registered
[ 3.885613] ACPI: bus type pci registered
[ 3.885754] PCI: PCI BIOS revision 2.10 entry at 0xfd8f7, last bus=14
[ 3.885758] PCI: Using configuration type 1
[ 3.885761] Setting up standard PCI resources
[ 3.889340] ACPI: EC: Found ECDT
[ 3.897858] ACPI: Interpreter enabled
[ 3.897862] ACPI: (supports S0 S3 S4 S5)
[ 3.897877] ACPI: Using IOAPIC for interrupt routing
[ 3.904931] ACPI: EC: GPE=0x1c, ports=0x66, 0x62
[ 3.904969] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 3.904977] PCI: Probing PCI hardware (bus 00)
[ 3.905602] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 3.905608] PCI quirk: region 1180-11bf claimed by ICH6 GPIO
[ 3.906278] PCI: Transparent bridge - 0000:00:1e.0
[ 3.906390] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 3.906547] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 3.906659] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
[ 3.906777] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
[ 3.906897] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 3.909876] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
[ 3.910074] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
[ 3.910269] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
[ 3.910463] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
[ 3.910657] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
[ 3.910852] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
[ 3.911046] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
[ 3.911241] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
[ 3.911539] ACPI: Power Resource [PUBS] (on)
[ 3.911551] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 3.911559] pnp: PnP ACPI init
[ 3.911569] ACPI: bus type pnp registered
[ 3.914871] pnp: PnP ACPI: found 14 devices
[ 3.914875] ACPI: ACPI bus type pnp unregistered
[ 3.914879] PnPBIOS: Disabled by ACPI PNP
[ 3.914912] PCI: Using ACPI for IRQ routing
[ 3.914916] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 3.943571] NET: Registered protocol family 8
[ 3.943575] NET: Registered protocol family 20
[ 3.943614] pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 3.943619] pnp: 00:00: iomem range 0xc0000-0xc3fff could not be reserved
[ 3.943623] pnp: 00:00: iomem range 0xc4000-0xc7fff could not be reserved
[ 3.943627] pnp: 00:00: iomem range 0xc8000-0xcbfff could not be reserved
[ 3.943634] pnp: 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
[ 3.943639] pnp: 00:02: iomem range 0xf0008000-0xf000bfff could not be reserved
[ 3.943644] pnp: 00:02: iomem range 0xfed14000-0xfed17fff could not be reserved
[ 3.943650] pnp: 00:02: iomem range 0xfed18000-0xfed18fff could not be reserved
[ 3.945288] Time: tsc clocksource has been installed.
[ 3.973822] PCI: Bridge: 0000:00:01.0
[ 3.973825] IO window: 3000-3fff
[ 3.973829] MEM window: b0100000-b01fffff
[ 3.973833] PREFETCH window: c0000000-c7ffffff
[ 3.973838] PCI: Bridge: 0000:00:1c.0
[ 3.973840] IO window: disabled.
[ 3.973847] MEM window: b0200000-b02fffff
[ 3.973852] PREFETCH window: disabled.
[ 3.973858] PCI: Bridge: 0000:00:1c.2
[ 3.973862] IO window: 4000-4fff
[ 3.973869] MEM window: b2000000-b3ffffff
[ 3.973874] PREFETCH window: c8000000-c80fffff
[ 3.973883] PCI: Bus 12, cardbus bridge: 0000:0b:00.0
[ 3.973886] IO window: 00005000-000050ff
[ 3.973892] IO window: 00005400-000054ff
[ 3.973899] PREFETCH window: d0000000-d3ffffff
[ 3.973905] MEM window: b8000000-bbffffff
[ 3.973911] PCI: Bridge: 0000:00:1e.0
[ 3.973915] IO window: 5000-8fff
[ 3.973922] MEM window: b4000000-bfffffff
[ 3.973927] PREFETCH window: d0000000-d7ffffff
[ 3.973942] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 3.973950] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 3.973969] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 17
[ 3.973977] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 3.973997] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 22 (level, low) -> IRQ 18
[ 3.974004] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 3.974016] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 3.974032] ACPI: PCI Interrupt 0000:0b:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 3.974047] NET: Registered protocol family 2
[ 4.013192] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 4.013253] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 4.014022] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 4.014265] TCP: Hash tables configured (established 131072 bind 65536)
[ 4.014270] TCP reno registered
[ 4.025289] checking if image is initramfs... it is
[ 4.476426] Switched to high resolution mode on CPU 0
[ 4.605357] Freeing initrd memory: 6734k freed
[ 4.605507] Simple Boot Flag at 0x35 set to 0x1
[ 4.605717] audit: initializing netlink socket (disabled)
[ 4.605736] audit(1203608981.160:1): initialized
[ 4.605793] highmem bounce pool size: 64 pages
[ 4.607255] VFS: Disk quotas dquot_6.5.1
[ 4.607268] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 4.607358] io scheduler noop registered
[ 4.607363] io scheduler anticipatory registered
[ 4.607366] io scheduler deadline registered
[ 4.607380] io scheduler cfq registered (default)
[ 4.607473] Boot video device is 0000:01:00.0
[ 4.607544] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 4.607569] assign_interrupt_mode Found MSI capability
[ 4.607574] Allocate Port Service[0000:00:01.0:pcie00]
[ 4.607637] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 4.607686] assign_interrupt_mode Found MSI capability
[ 4.607690] Allocate Port Service[0000:00:1c.0:pcie00]
[ 4.607713] Allocate Port Service[0000:00:1c.0:pcie02]
[ 4.607795] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 4.607843] assign_interrupt_mode Found MSI capability
[ 4.607848] Allocate Port Service[0000:00:1c.2:pcie00]
[ 4.607870] Allocate Port Service[0000:00:1c.2:pcie02]
[ 4.607998] isapnp: Scanning for PnP cards...
[ 4.962381] isapnp: No Plug & Play device found
[ 4.982688] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 4.983732] pnp: Device 00:0a activated.
[ 4.983914] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
[ 4.984110] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 23 (level, low) -> IRQ 19
[ 4.984121] ACPI: PCI interrupt for device 0000:00:1e.3 disabled
[ 4.984512] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 4.984677] input: Macintosh mouse button emulation as /class/input/input0
[ 4.984745] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 4.993087] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.993094] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 4.993210] mice: PS/2 mouse device common for all mice
[ 4.993287] EISA: Probing bus 0 at eisa.0
[ 4.993296] Cannot allocate resource for EISA slot 1
[ 4.993300] Cannot allocate resource for EISA slot 2
[ 4.993303] Cannot allocate resource for EISA slot 3
[ 4.993306] Cannot allocate resource for EISA slot 4
[ 4.993310] Cannot allocate resource for EISA slot 5
[ 4.993313] Cannot allocate resource for EISA slot 6
[ 4.993316] Cannot allocate resource for EISA slot 7
[ 4.993319] Cannot allocate resource for EISA slot 8
[ 4.993323] EISA: Detected 0 cards.
[ 4.993409] TCP cubic registered
[ 4.993423] NET: Registered protocol family 1
[ 4.993446] Using IPI Shortcut mode
[ 4.993598] Magic number: 12:929:841
[ 4.993663] hash matches device ptyu7
[ 4.993672] hash matches device ptyra
[ 4.993877] Freeing unused kernel memory: 348k freed
[ 5.031498] input: AT Translated Set 2 keyboard as /class/input/input1
[ 5.063139] vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 3072k, total 65472k
[ 5.063149] vesafb: mode is 1024x768x16, linelength=2048, pages=41
[ 5.063152] vesafb: protected mode interface info at c000:5b63
[ 5.063156] vesafb: pmi: set display start = c00c5bd1, set palette = c00c5c0b
[ 5.063160] vesafb: pmi: ports = 3010 3016 3054 3038 303c 305c 3000 3004 30b0 30b2 30b4
[ 5.063168] vesafb: scrolling: redraw
[ 5.063172] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 5.063250] Console: switching to colour frame buffer device 128x48
[ 5.084838] fb0: VESA VGA frame buffer device
[ 5.188529] vga16fb: initializing
[ 5.188533] vga16fb: mapped to 0xc00a0000
[ 5.188741] fb1: VGA16 VGA frame buffer device
[ 5.201094] fuse init (API version 7.8)
[ 5.205017] Capability LSM initialized
[ 5.212785] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 5.213048] ACPI: Processor [CPU] (supports 8 throttling states)
[ 5.214709] ACPI: Thermal Zone [THM0] (71 C)
[ 5.549954] usbcore: registered new interface driver usbfs
[ 5.550206] usbcore: registered new interface driver hub
[ 5.550438] usbcore: registered new device driver usb
[ 5.551292] USB Universal Host Controller Interface driver v3.0
[ 5.551584] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 5.551900] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 5.551904] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 5.552279] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 5.559536] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001800
[ 5.566922] usb usb1: configuration #1 chosen from 1 choice
[ 5.574397] hub 1-0:1.0: USB hub found
[ 5.581935] hub 1-0:1.0: 2 ports detected
[ 5.690488] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 20
[ 5.698368] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 5.698372] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 5.706283] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 5.714339] uhci_hcd 0000:00:1d.1: irq 20, io base 0x00001820
[ 5.722430] usb usb2: configuration #1 chosen from 1 choice
[ 5.730532] hub 2-0:1.0: USB hub found
[ 5.738607] hub 2-0:1.0: 2 ports detected
[ 5.766569] SCSI subsystem initialized
[ 5.779220] libata version 2.21 loaded.
[ 5.850230] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 21
[ 5.858570] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 5.858574] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 5.866812] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 5.875057] uhci_hcd 0000:00:1d.2: irq 21, io base 0x00001840
[ 5.883203] usb usb3: configuration #1 chosen from 1 choice
[ 5.891229] hub 3-0:1.0: USB hub found
[ 5.899154] hub 3-0:1.0: 2 ports detected
[ 5.938182] Floppy drive(s): fd0 is 1.44M
[ 5.989253] FDC 0 is a National Semiconductor PC87306
[ 6.010122] tg3.c:v3.77 (May 31, 2007)
[ 6.017864] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 6.025813] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 2.588000] Marking TSC unstable due to: possible TSC halt in C2.
[ 2.596000] Time: acpi_pm clocksource has been installed.
[ 2.640000] eth0: Tigon3 [partno(BCM95751M) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:10:c6:d0:e9:2b
[ 2.648000] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[ 2.656000] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 2.664000] usb 2-1: new low speed USB device using uhci_hcd and address 2
[ 2.676000] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) -> IRQ 22
[ 2.684000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.684000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.692000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
[ 2.700000] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.708000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.708000] ehci_hcd 0000:00:1d.7: irq 22, io mem 0xb0000000
[ 2.804000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.812000] usb usb4: configuration #1 chosen from 1 choice
[ 2.820000] hub 4-0:1.0: USB hub found
[ 2.828000] hub 4-0:1.0: 8 ports detected
[ 2.940000] ata_piix 0000:00:1f.2: version 2.11
[ 2.940000] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[ 3.032000] Clocksource tsc unstable (delta = -227820312 ns)
[ 3.104000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 3.104000] scsi0 : ata_piix
[ 3.112000] scsi1 : ata_piix
[ 3.120000] ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x000118c0 irq 14
[ 3.128000] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x000118c8 irq 15
[ 3.220000] usb 2-1: device not accepting address 2, error -71
[ 3.472000] ata1.00: ATA-6: FUJITSU MHT2040AH, 8471, max UDMA/100
[ 3.480000] ata1.00: 78140160 sectors, multi 16: LBA
[ 3.488000] ata1.00: applying bridge limits
[ 3.512000] ata1.00: configured for UDMA/100
[ 3.840000] ata2.00: ATAPI: HL-DT-STCD-RW/DVD DRIVE GCC-4242N, 0J04, max UDMA/33
[ 4.020000] ata2.00: configured for UDMA/33
[ 4.028000] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHT2040A 8471 PQ: 0 ANSI: 5
[ 4.040000] scsi 1:0:0:0: CD-ROM HL-DT-ST RW/DVD GCC-4242N 0J04 PQ: 0 ANSI: 5
[ 4.056000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 22
[ 4.064000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 4.064000] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 4.072000] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 4.080000] uhci_hcd 0000:00:1d.3: irq 22, io base 0x00001860
[ 4.092000] usb usb5: configuration #1 chosen from 1 choice
[ 4.100000] usb 2-1: new low speed USB device using uhci_hcd and address 4
[ 4.108000] hub 5-0:1.0: USB hub found
[ 4.120000] hub 5-0:1.0: 2 ports detected
[ 4.140000] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
[ 4.148000] sd 0:0:0:0: [sda] Write Protect is off
[ 4.156000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.156000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.168000] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
[ 4.176000] sd 0:0:0:0: [sda] Write Protect is off
[ 4.184000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.184000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.192000] sda: sda1 sda2 < sda5 >
[ 4.296000] usb 2-1: configuration #1 chosen from 1 choice
[ 4.304000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.332000] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 4.340000] Uniform CD-ROM driver Revision: 3.20
[ 4.352000] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 4.352000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.364000] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 4.560000] usb 3-2: new full speed USB device using uhci_hcd and address 2
[ 4.636000] Attempting manual resume
[ 4.644000] swsusp: Resume From Partition 8:5
[ 4.644000] PM: Checking swsusp image.
[ 4.644000] PM: Resume from disk failed.
[ 4.696000] kjournald starting. Commit interval 5 seconds
[ 4.708000] EXT3-fs: mounted filesystem with ordered data mode.
[ 4.752000] usb 3-2: configuration #1 chosen from 1 choice
[ 4.756000] usbcore: registered new interface driver hiddev
[ 4.768000] input: USB Mouse as /class/input/input2
[ 4.768000] input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:1d.1-1
[ 4.768000] usbcore: registered new interface driver usbhid
[ 4.768000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 14.212000] Linux agpgart interface v0.102 (c) Dave Jones
[ 14.244000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 14.252000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 15.288000] Yenta: CardBus bridge found at 0000:0b:00.0 [1014:056c]
[ 15.424000] Yenta: ISA IRQ mask 0x04b8, PCI irq 16
[ 15.432000] Socket status: 30000006
[ 15.440000] pcmcia: parent PCI bridge I/O window: 0x5000 - 0x8fff
[ 15.448000] cs: IO port probe 0x5000-0x8fff: clean.
[ 15.456000] pcmcia: parent PCI bridge Memory window: 0xb4000000 - 0xbfffffff
[ 15.464000] pcmcia: parent PCI bridge Memory window: 0xd0000000 - 0xd7ffffff
[ 15.504000] iTCO_vendor_support: vendor-support=0
[ 15.540000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
[ 15.548000] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[ 15.556000] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 15.604000] intel_rng: FWH not detected
[ 15.632000] input: PC Speaker as /class/input/input3
[ 15.656000] Real Time Clock Driver v1.12ac
[ 15.676000] ieee80211_crypt: registered algorithm 'NULL'
[ 15.692000] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 15.700000] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 16.036000] cs: IO port probe 0x100-0x3af: clean.
[ 16.048000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 16.056000] cs: IO port probe 0x820-0x8ff: clean.
[ 16.064000] cs: IO port probe 0xc00-0xcf7: clean.
[ 16.072000] cs: IO port probe 0xa00-0xaff: clean.
[ 16.272000] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x2c6ab1, caps: 0x884793/0x0
[ 16.280000] serio: Synaptics pass-through port at isa0060/serio1/input0
[ 16.324000] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq
[ 16.336000] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 16.344000] ACPI: PCI Interrupt 0000:0b:02.0[A] -> GSI 21 (level, low) -> IRQ 23
[ 16.352000] input: SynPS/2 Synaptics TouchPad as /class/input/input4
[ 16.360000] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 16.368000] parport_pc 00:0b: reported by Plug and Play ACPI
[ 16.376000] parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
[ 16.504000] irda_init()
[ 16.504000] NET: Registered protocol family 23
[ 16.568000] pnp: Device 00:0c activated.
[ 16.576000] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
[ 16.576000] nsc-ircc, chip->init
[ 16.584000] nsc-ircc, Found chip at base=0x02e
[ 16.592000] nsc-ircc, driver loaded (Dag Brattli)
[ 17.140000] ipw2200: ipw2200-bss.fw request_firmware failed: Reason -2
[ 17.148000] ipw2200: Unable to load firmware: -2
[ 17.156000] ipw2200: failed to register network device
[ 17.164000] ACPI: PCI interrupt for device 0000:0b:02.0 disabled
[ 17.172000] IrDA: Registered device irda0
[ 17.180000] nsc-ircc, Using dongle: IBM31T1100 or Temic TFDS6000/TFDS6500
[ 17.204000] ipw2200: probe of 0000:0b:02.0 failed with error -5
[ 17.444000] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 22 (level, low) -> IRQ 18
[ 17.452000] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 18.380000] intel8x0_measure_ac97_clock: measured 55487 usecs
[ 18.388000] intel8x0: clocking to 48000
[ 19.124000] loop: module loaded
[ 19.160000] lp0: using parport0 (interrupt-driven).
[ 19.248000] Adding 1646620k swap on /dev/sda5. Priority:-1 extents:1 across:1646620k
[ 19.592000] EXT3 FS on sda1, internal journal
[ 21.416000] input: Power Button (FF) as /class/input/input5
[ 21.420000] ACPI: Power Button (FF) [PWRF]
[ 21.456000] input: Lid Switch as /class/input/input6
[ 21.456000] ACPI: Lid Switch [LID]
[ 21.492000] input: Sleep Button (CM) as /class/input/input7
[ 21.496000] ACPI: Sleep Button (CM) [SLPB]
[ 21.548000] ACPI: ACPI Dock Station Driver
[ 21.580000] ACPI: AC Adapter [AC] (on-line)
[ 21.604000] ACPI: Battery Slot [BAT0] (battery present)
[ 21.620000] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
[ 21.632000] ACPI: \_SB_.PCI0.IDE0.SCND.MSTR: found ejectable bay
[ 21.632000] ACPI: \_SB_.PCI0.IDE0.SCND.MSTR: Adding notify handler
[ 21.632000] ACPI: Error installing bay notify handler
[ 21.632000] ACPI: Bay [\_SB_.PCI0.IDE0.SCND.MSTR] Added
[ 21.768000] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[ 21.988000] input: TPPS/2 IBM TrackPoint as /class/input/input8
[ 23.088000] ppdev: user-space parallel port driver
[ 23.684000] IBM machine detected. Enabling interrupts during APM calls.
[ 23.684000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 23.684000] apm: overridden by ACPI.
[ 23.864000] thinkpad_acpi: ThinkPad ACPI Extras v0.14
[ 23.864000] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 23.864000] thinkpad_acpi: ThinkPad EC firmware 1YHT29WW-1.06
[ 23.868000] thinkpad_acpi: another device driver is already handling bay events
[ 23.868000] thinkpad_acpi: disabling subdriver bay
[ 23.868000] thinkpad_acpi: fan_init: initial fan status is unknown, assuming it is in auto mode
[ 24.020000] Capability LSM initialized
[ 24.192000] Bluetooth: Core ver 2.11
[ 24.192000] NET: Registered protocol family 31
[ 24.192000] Bluetooth: HCI device and connection manager initialized
[ 24.192000] Bluetooth: HCI socket layer initialized
[ 24.220000] Bluetooth: L2CAP ver 2.8
[ 24.220000] Bluetooth: L2CAP socket layer initialized
[ 24.336000] Bluetooth: RFCOMM socket layer initialized
[ 24.336000] Bluetooth: RFCOMM TTY layer initialized
[ 24.336000] Bluetooth: RFCOMM ver 1.8
[ 24.944000] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 24.944000] tg3: eth0: Flow control is on for TX and on for RX.
[ 26.388000] [drm] Initialized drm 1.1.0 20060810
[ 26.460000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 26.460000] [drm] Initialized radeon 1.27.0 20060524 on minor 0
[ 29.576000] NET: Registered protocol family 17
[ 30.028000] [drm] Setting GART location based on new memory map
[ 30.028000] [drm] Loading R300 Microcode
[ 30.028000] [drm] writeback test succeeded in 1 usecs
[ 36.500000] NET: Registered protocol family 10
[ 36.500000] lo: Disabled Privacy Extensions
[ 46.880000] eth0: no IPv6 routers present
[ 820.240000] pcmcia: Detected deprecated PCMCIA ioctl usage from process: lshw.
[ 820.240000] pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
[ 820.240000] pcmcia: see http://www.kernel.org/pub/linux/utils/k ... cmcia.html for details.

才发现加在无线网卡失败,如何解决呢?


页首
 用户资料  
 
2 楼 
 文章标题 :
帖子发表于 : 2008-02-22 0:13 
头像

注册: 2005-08-14 21:55
帖子: 58428
地址: 长沙
送出感谢: 4
接收感谢: 272
多用grep哦。这看晕的。
多用iwlist iwconfig看。


_________________
● 鸣学


页首
 用户资料  
 
显示帖子 :  排序  
发表新帖 回复这个主题  [ 2 篇帖子 ] 

当前时区为 UTC + 8 小时


在线用户

正在浏览此版面的用户:没有注册用户 和 3 位游客


不能 在这个版面发表主题
不能 在这个版面回复主题
不能 在这个版面编辑帖子
不能 在这个版面删除帖子
不能 在这个版面提交附件

前往 :  
本站点为公益性站点,用于推广开源自由软件,由 DiaHosting VPSBudgetVM VPS 提供服务。
我们认为:软件应可免费取得,软件工具在各种语言环境下皆可使用,且不会有任何功能上的差异;
人们应有定制和修改软件的自由,且方式不受限制,只要他们自认为合适。

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
简体中文语系由 王笑宇 翻译