当前时区为 UTC + 8 小时



发表新帖 回复这个主题  [ 3 篇帖子 ] 
作者 内容
1 楼 
 文章标题 : athreos ar5418(ar5008) 可以连接上路由 无法打开网页 (已解决)
帖子发表于 : 2008-06-05 20:36 

注册: 2006-08-30 16:50
帖子: 74
地址: 四川
送出感谢: 0 次
接收感谢: 0 次
好不容易使用 ndiswrapper 安装好ath的 netathw驱动 版本为 :01/17/2008 7.4.2.75
可以使用漫游模式连接到我的路由 ping我们这边的dns也可以ping通 但是就是无法打开网页 连接老是超时
查看硬件驱动中 的 Support for Atheros 802.11 wireless LAN cards 启动状态为正常 但是状态为未使用

很是郁闷啊 使用madwifi也无法连接 有高手能帮帮忙么?

ping的信息:
代码:
64 bytes from 61.139.2.69: icmp_seq=1023 ttl=249 time=16.2 ms

64 bytes from 61.139.2.69: icmp_seq=1024 ttl=249 time=15.7 ms

64 bytes from 61.139.2.69: icmp_seq=1025 ttl=249 time=15.7 ms

64 bytes from 61.139.2.69: icmp_seq=1026 ttl=249 time=19.1 ms

64 bytes from 61.139.2.69: icmp_seq=1027 ttl=249 time=39.4 ms

64 bytes from 61.139.2.69: icmp_seq=1028 ttl=249 time=64.0 ms

64 bytes from 61.139.2.69: icmp_seq=1029 ttl=249 time=15.9 ms

64 bytes from 61.139.2.69: icmp_seq=1030 ttl=249 time=14.7 ms

64 bytes from 61.139.2.69: icmp_seq=1031 ttl=249 time=15.5 ms

64 bytes from 61.139.2.69: icmp_seq=1032 ttl=249 time=15.2 ms

64 bytes from 61.139.2.69: icmp_seq=1033 ttl=249 time=16.5 ms

64 bytes from 61.139.2.69: icmp_seq=1034 ttl=249 time=17.5 ms

64 bytes from 61.139.2.69: icmp_seq=1035 ttl=249 time=15.8 ms

64 bytes from 61.139.2.69: icmp_seq=1036 ttl=249 time=16.5 ms

64 bytes from 61.139.2.69: icmp_seq=1037 ttl=249 time=14.6 ms

64 bytes from 61.139.2.69: icmp_seq=1038 ttl=249 time=14.3 ms

64 bytes from 61.139.2.69: icmp_seq=1039 ttl=249 time=15.2 ms

64 bytes from 61.139.2.69: icmp_seq=1040 ttl=249 time=19.2 ms



--- 61.139.2.69 ping statistics ---

1040 packets transmitted, 971 received, 6% packet loss, time 1050087ms

rtt min/avg/max/mdev = 13.336/34.037/2422.451/150.279 ms, pipe 3


dmesg的部分信息
代码:
[   21.644716] Console: colour VGA+ 80x25

[   21.644724] console [tty0] enabled

[   21.645774] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

[   21.646759] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

[   21.845951] Memory: 1805608k/1833472k available (2176k kernel code, 26604k reserved, 1007k data, 368k init, 915968k highmem)

[   21.845967] virtual kernel memory layout:

[   21.845970]     fixmap  : 0xfff4b000 - 0xfffff000   ( 720 kB)

[   21.845973]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)

[   21.845976]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)

[   21.845978]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)

[   21.845981]       .init : 0xc0421000 - 0xc047d000   ( 368 kB)

[   21.845984]       .data : 0xc0320134 - 0xc041bdc4   (1007 kB)

[   21.845987]       .text : 0xc0100000 - 0xc0320134   (2176 kB)

[   21.845994] Checking if this processor honours the WP bit even in supervisor mode... Ok.

[   21.846083] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1

[   21.926046] Calibrating delay using timer specific routine.. 3739.09 BogoMIPS (lpj=7478186)

[   21.926104] Security Framework initialized

[   21.926121] SELinux:  Disabled at boot.

[   21.926151] AppArmor: AppArmor initialized

[   21.926160] Failure registering capabilities with primary security module.

[   21.926177] Mount-cache hash table entries: 512

[   21.926433] Initializing cgroup subsys ns

[   21.926444] Initializing cgroup subsys cpuacct

[   21.926464] CPU: After generic identify, caps: bfe9fbff 00000000 00000000 00000000 0000c189 00000000 00000000 00000000

[   21.926481] monitor/mwait feature present.

[   21.926485] using mwait in idle threads.

[   21.926493] CPU: L1 I cache: 32K, L1 D cache: 32K

[   21.926498] CPU: L2 cache: 2048K

[   21.926504] CPU: Physical Processor ID: 0

[   21.926507] CPU: Processor Core ID: 0

[   21.926512] CPU: After all inits, caps: bfe9fbff 00000000 00000000 00002940 0000c189 00000000 00000000 00000000

[   21.926534] Compat vDSO mapped to ffffe000.

[   21.926561] Checking 'hlt' instruction... OK.

[   21.942791] SMP alternatives: switching to UP code

[   21.946403] Early unpacking initramfs... done

[   22.695712] ACPI: Core revision 20070126

[   22.695825] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.

[   23.108490] CPU0: Intel(R) Core(TM) Duo CPU      T2350  @ 1.86GHz stepping 0c

[   23.108522] SMP alternatives: switching to SMP code

[   23.109830] Booting processor 1/1 eip 3000

[   23.120353] Initializing CPU#1

[   23.196838] Calibrating delay using timer specific routine.. 3733.94 BogoMIPS (lpj=7467881)

[   23.196852] CPU: After generic identify, caps: bfe9fbff 00000000 00000000 00000000 0000c189 00000000 00000000 00000000

[   23.196863] monitor/mwait feature present.

[   23.196869] CPU: L1 I cache: 32K, L1 D cache: 32K

[   23.196873] CPU: L2 cache: 2048K

[   23.196878] CPU: Physical Processor ID: 0

[   23.196881] CPU: Processor Core ID: 1

[   23.196884] CPU: After all inits, caps: bfe9fbff 00000000 00000000 00002940 0000c189 00000000 00000000 00000000

[   23.197889] CPU1: Intel(R) Core(TM) Duo CPU      T2350  @ 1.86GHz stepping 0c

[   23.197932] Total of 2 processors activated (7473.03 BogoMIPS).

[   23.198124] ENABLING IO-APIC IRQs

[   23.198358] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1

[   23.344918] checking TSC synchronization [CPU#0 -> CPU#1]: passed.

[   23.364933] Brought up 2 CPUs

[   23.364977] CPU0 attaching sched-domain:

[   23.364982]  domain 0: span 03

[   23.364987]   groups: 01 02

[   23.364993] CPU1 attaching sched-domain:

[   23.364997]  domain 0: span 03

[   23.365001]   groups: 02 01

[   23.365489] net_namespace: 64 bytes

[   23.365500] Booting paravirtualized kernel on bare hardware

[   23.366451] Time: 19:56:48  Date: 06/05/08

[   23.366506] NET: Registered protocol family 16

[   23.366949] EISA bus registered

[   23.366959] ACPI: bus type pci registered

[   23.383649] PCI: PCI BIOS revision 2.10 entry at 0xfd5c4, last bus=10

[   23.383655] PCI: Using configuration type 1

[   23.383659] Setting up standard PCI resources

[   23.387105] ACPI: EC: Look up EC in DSDT

[   23.392451] ACPI: Interpreter enabled

[   23.392457] ACPI: (supports S0 S3 S4 S5)

[   23.392484] ACPI: Using IOAPIC for interrupt routing

[   23.393136] ACPI: EC: non-query interrupt received, switching to interrupt mode

[   23.402066] ACPI: EC: GPE = 0x3, I/O: command/status = 0x66, data = 0x62

[   23.402072] ACPI: EC: driver started in interrupt mode

[   23.402161] ACPI: PCI Root Bridge [PCI0] (0000:00)

[   23.404697] PCI: Transparent bridge - 0000:00:14.4

[   23.404754] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]

[   23.405207] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]

[   23.405439] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]

[   23.405704] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]

[   23.405884] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]

[   23.410697] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.

[   23.410909] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.

[   23.411114] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.

[   23.411320] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.

[   23.411526] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.

[   23.411732] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.

[   23.411938] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.

[   23.412144] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.

[   23.412350] ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled.

[   23.412596] Linux Plug and Play Support v0.97 (c) Adam Belay

[   23.412691] pnp: PnP ACPI init

[   23.412706] ACPI: bus type pnp registered

[   23.416809] pnp: PnP ACPI: found 10 devices

[   23.416814] ACPI: ACPI bus type pnp unregistered

[   23.416821] PnPBIOS: Disabled by ACPI PNP

[   23.417337] PCI: Using ACPI for IRQ routing

[   23.417342] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report

[   23.417352] PCI: Cannot allocate resource region 7 of bridge 0000:00:06.0

[   23.417357] PCI: Cannot allocate resource region 8 of bridge 0000:00:06.0

[   23.476827] NET: Registered protocol family 8

[   23.476831] NET: Registered protocol family 20

[   23.476956] AppArmor: AppArmor Filesystem Enabled

[   23.480591] Time: tsc clocksource has been installed.

[   23.496869] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved

[   23.496891] system 00:08: ioport range 0x1080-0x1080 has been reserved

[   23.496897] system 00:08: ioport range 0x200-0x20f has been reserved

[   23.496904] system 00:08: ioport range 0x220-0x22f has been reserved

[   23.496910] system 00:08: ioport range 0x40b-0x40b has been reserved

[   23.496916] system 00:08: ioport range 0x4d0-0x4d1 has been reserved

[   23.496922] system 00:08: ioport range 0x4d6-0x4d6 has been reserved

[   23.496928] system 00:08: ioport range 0x530-0x537 has been reserved

[   23.496934] system 00:08: ioport range 0xc00-0xc01 has been reserved

[   23.496941] system 00:08: ioport range 0xc14-0xc14 has been reserved

[   23.496947] system 00:08: ioport range 0xc50-0xc52 has been reserved

[   23.496953] system 00:08: ioport range 0xc6c-0xc6c has been reserved

[   23.496959] system 00:08: ioport range 0xc6f-0xc6f has been reserved

[   23.496965] system 00:08: ioport range 0xcd4-0xcd5 has been reserved

[   23.496972] system 00:08: ioport range 0xcd6-0xcd7 has been reserved

[   23.496978] system 00:08: ioport range 0xcd8-0xcdf has been reserved

[   23.496984] system 00:08: ioport range 0x8000-0x805f has been reserved

[   23.496991] system 00:08: ioport range 0x8210-0x821f has been reserved

[   23.496997] system 00:08: ioport range 0xf40-0xf47 has been reserved

[   23.497003] system 00:08: ioport range 0x280-0x293 has been reserved

[   23.497009] system 00:08: ioport range 0x87f-0x87f has been reserved

[   23.497023] system 00:09: iomem range 0xe0000-0xfffff could not be reserved

[   23.497030] system 00:09: iomem range 0xfff00000-0xffffffff could not be reserved

[   23.497037] system 00:09: iomem range 0x0-0xfff could not be reserved

[   23.527930] PCI: Bridge: 0000:00:01.0

[   23.527936]   IO window: 9000-9fff

[   23.527943]   MEM window: c0000000-c00fffff

[   23.527950]   PREFETCH window: d0000000-dfffffff

[   23.527957] PCI: Bridge: 0000:00:04.0

[   23.527960]   IO window: disabled.

[   23.527967]   MEM window: c0100000-c01fffff

[   23.527972]   PREFETCH window: disabled.

[   23.527979] PCI: Bridge: 0000:00:06.0

[   23.527982]   IO window: disabled.

[   23.527988]   MEM window: disabled.

[   23.527993]   PREFETCH window: disabled.

[   23.528010] PCI: Bridge: 0000:00:14.4

[   23.528016]   IO window: a000-afff

[   23.528026]   MEM window: f0200000-f02fffff

[   23.528034]   PREFETCH window: f0300000-f03fffff

[   23.528073] PCI: Setting latency timer of device 0000:00:04.0 to 64

[   23.528093] PCI: Setting latency timer of device 0000:00:06.0 to 64

[   23.528125] NET: Registered protocol family 2

[   23.564844] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)

[   23.565308] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)

[   23.566805] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)

[   23.567573] TCP: Hash tables configured (established 131072 bind 65536)

[   23.567579] TCP reno registered

[   23.577008] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0

[   24.028287] Switched to high resolution mode on CPU 1

[   24.297688]  it is

[   25.068786] Freeing initrd memory: 7281k freed

[   25.070557] audit: initializing netlink socket (disabled)

[   25.070583] audit(1212695808.700:1): initialized

[   25.071022] highmem bounce pool size: 64 pages

[   25.075435] VFS: Disk quotas dquot_6.5.1

[   25.075593] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[   25.075869] io scheduler noop registered

[   25.075874] io scheduler anticipatory registered

[   25.075878] io scheduler deadline registered

[   25.075902] io scheduler cfq registered (default)

[   25.075993] Boot video device is 0000:01:05.0

[   25.076235] PCI: Setting latency timer of device 0000:00:04.0 to 64

[   25.076292] assign_interrupt_mode Found MSI capability

[   25.076352] Allocate Port Service[0000:00:04.0:pcie00]

[   25.076499] PCI: Setting latency timer of device 0000:00:06.0 to 64

[   25.076555] assign_interrupt_mode Found MSI capability

[   25.076608] Allocate Port Service[0000:00:06.0:pcie00]

[   25.077135] isapnp: Scanning for PnP cards...

[   25.434570] isapnp: No Plug & Play device found

[   25.495081] Real Time Clock Driver v1.12ac

[   25.495305] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled

[   25.497966] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize

[   25.498131] input: Macintosh mouse button emulation as /devices/virtual/input/input0

[   25.498346] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12

[   25.502530] i8042.c: Detected active multiplexing controller, rev 1.1.

[   25.504290] serio: i8042 KBD port at 0x60,0x64 irq 1

[   25.504300] serio: i8042 AUX0 port at 0x60,0x64 irq 12

[   25.504307] serio: i8042 AUX1 port at 0x60,0x64 irq 12

[   25.504312] serio: i8042 AUX2 port at 0x60,0x64 irq 12

[   25.504318] serio: i8042 AUX3 port at 0x60,0x64 irq 12

[   25.523607] mice: PS/2 mouse device common for all mice

[   25.523847] EISA: Probing bus 0 at eisa.0

[   25.523863] Cannot allocate resource for EISA slot 1

[   25.523909] Cannot allocate resource for EISA slot 8

[   25.523913] EISA: Detected 0 cards.

[   25.523920] cpuidle: using governor ladder

[   25.523924] cpuidle: using governor menu

[   25.524103] NET: Registered protocol family 1

[   25.524154] Using IPI No-Shortcut mode

[   25.524220] registered taskstats version 1

[   25.524433]   Magic number: 12:281:950

[   25.524448]   hash matches device ttya5

[   25.524568]   hash matches device tty7

[   25.524596] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found

[   25.524600] EDD information not available.

[   25.525119] Freeing unused kernel memory: 368k freed

[   25.559023] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1

[   26.978269] fuse init (API version 7.9)

[   27.021222] ACPI: SSDT 6FE8DFBC, 0252 (r1  PmRef  Cpu0Ist     3000 INTL 20050228)

[   27.022267] ACPI: SSDT 6FE8DD47, 01F0 (r1  PmRef  Cpu0Cst     3001 INTL 20050228)

[   27.023147] ACPI: CPU0 (power states: C1[C1] C3[C3])

[   27.023158] ACPI: Processor [CPU0] (supports 8 throttling states)

[   27.023652] ACPI: SSDT 6FE8E20E, 0087 (r1  PmRef  Cpu1Ist     3000 INTL 20050228)

[   27.024000] ACPI: SSDT 6FE8DF37, 0085 (r1  PmRef  Cpu1Cst     3000 INTL 20050228)

[   27.024760] ACPI: CPU1 (power states: C1[C1] C3[C3])

[   27.024770] ACPI: Processor [CPU1] (supports 8 throttling states)

[   27.028918] ACPI: Thermal Zone [THRM] (53 C)

[   27.377009] SCSI subsystem initialized

[   27.420195] usbcore: registered new interface driver usbfs

[   27.420239] usbcore: registered new interface driver hub

[   27.420291] libata version 3.00 loaded.

[   27.423418] usbcore: registered new device driver usb

[   27.429656] sata_sil 0000:00:12.0: version 2.3

[   27.429751] PCI: Enabling device 0000:00:12.0 (0005 -> 0007)

[   27.429768] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 16

[   27.444551] scsi0 : sata_sil

[   27.471750] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver

[   27.484457] scsi1 : sata_sil

[   27.485023] ata1: SATA max UDMA/100 mmio m512@0xc0507000 tf 0xc0507080 irq 16

[   27.485032] ata2: SATA max UDMA/100 mmio m512@0xc0507000 tf 0xc05070c0 irq 16

[   27.916792] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2

[   27.916804] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

[   27.951993] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)

[   28.011318] ata1.00: ATA-7: WDC WD800BEVS-22RST0, 04.01G04, max UDMA/133

[   28.011328] ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)

[   28.025467] ata1.00: configured for UDMA/100

[   28.046978] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)

[   28.335552] ata2: SATA link down (SStatus 0 SControl 300)

[   28.335802] scsi 0:0:0:0: Direct-Access     ATA      WDC WD800BEVS-22 04.0 PQ: 0 ANSI: 5

[   28.335998] ATIIXP: IDE controller (0x1002:0x4376 rev 0x80) at  PCI slot 0000:00:14.1

[   28.336039] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17

[   28.336059] ATIIXP: not 100% native mode: will probe irqs later

[   28.336075]     ide0: BM-DMA at 0x8420-0x8427, BIOS settings: hda:DMA, hdb:pio

[   28.336100]     ide1: BM-DMA at 0x8428-0x842f, BIOS settings: hdc:pio, hdd:pio

[   28.336117] Probing IDE interface ide0...

[   29.407879] hda: HL-DT-STCD-RW/DVD DRIVE GCC-T10N, ATAPI CD/DVD-ROM drive

[   29.407943] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4

[   29.408652] hda: UDMA/33 mode selected

[   29.409755] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

[   29.412180] Probing IDE interface ide1...

[   29.977942] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 18

[   29.977971] ohci_hcd 0000:00:13.0: OHCI Host Controller

[   29.978431] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1

[   29.978467] ohci_hcd 0000:00:13.0: irq 18, io mem 0xc0504000

[   30.035033] usb usb1: configuration #1 chosen from 1 choice

[   30.035088] hub 1-0:1.0: USB hub found

[   30.035109] hub 1-0:1.0: 4 ports detected

[   30.137839] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 18

[   30.137863] ohci_hcd 0000:00:13.1: OHCI Host Controller

[   30.137918] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2

[   30.137944] ohci_hcd 0000:00:13.1: irq 18, io mem 0xc0505000

[   30.193816] usb usb2: configuration #1 chosen from 1 choice

[   30.193864] hub 2-0:1.0: USB hub found

[   30.193881] hub 2-0:1.0: 4 ports detected

[   30.297681] 8139cp 0000:08:0b.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip

[   30.297691] 8139cp 0000:08:0b.0: Try the "8139too" driver instead.

[   30.297850] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 18

[   30.297869] ehci_hcd 0000:00:13.2: EHCI Host Controller

[   30.297919] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3

[   30.297996] ehci_hcd 0000:00:13.2: irq 18, io mem 0xc0506000

[   30.305234] 8139too Fast Ethernet driver 0.9.28

[   30.310499] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004

[   30.310711] usb usb3: configuration #1 chosen from 1 choice

[   30.310763] hub 3-0:1.0: USB hub found

[   30.310775] hub 3-0:1.0: 8 ports detected

[   30.414736] ACPI: PCI Interrupt 0000:08:0a.0[A] -> GSI 21 (level, low) -> IRQ 21

[   30.465562] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21]  MMIO=[f0200000-f02007ff]  Max Packet=[2048]  IR/IT contexts=[8/8]

[   30.499622] ACPI: PCI Interrupt 0000:08:0b.0[A] -> GSI 20 (level, low) -> IRQ 19

[   30.501169] eth0: RealTek RTL8139 at 0xa000, 00:03:0d:65:49:52, IRQ 19

[   30.501176] eth0:  Identified 8139 chip type 'RTL-8100B/8139D'

[   30.516876] Driver 'sd' needs updating - please use bus_type methods

[   30.517039] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)

[   30.517067] sd 0:0:0:0: [sda] Write Protect is off

[   30.517073] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

[   30.517111] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[   30.517206] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)

[   30.517234] sd 0:0:0:0: [sda] Write Protect is off

[   30.517240] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00

[   30.517291] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[   30.517299]  sda:<6>hda: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache

[   30.526519] Uniform CD-ROM driver Revision: 3.20

[   30.569154]  sda1 sda2 < sda5 sda6 sda7 > sda3 sda4

[   30.608896] sd 0:0:0:0: [sda] Attached SCSI disk

[   30.618315] sd 0:0:0:0: Attached scsi generic sg0 type 0

[   31.280066] Attempting manual resume

[   31.280073] swsusp: Resume From Partition 8:6

[   31.280077] PM: Checking swsusp image.

[   31.280310] PM: Resume from disk failed.

[   31.325825] kjournald starting.  Commit interval 5 seconds

[   31.325855] EXT3-fs: mounted filesystem with ordered data mode.

[   31.764382] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00030d4120015bc4]

[   42.669731] input: PC Speaker as /devices/platform/pcspkr/input/input2

[   42.957837] Linux agpgart interface v0.102

[   43.085413] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device

[   43.129298] pci_hotplug: PCI Hot Plug PCI Core version: 0.5

[   43.150301] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4

[   44.555897] ndiswrapper version 1.52 loaded (smp=yes, preempt=no)

[   44.643189] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04713/0x200000

[   44.669056] ACPI: AC Adapter [AC0] (on-line)

[   44.680667] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input3

[   44.740950] ACPI: Battery Slot [BAT0] (battery present)

[   44.819724] input: Power Button (FF) as /devices/virtual/input/input4

[   44.857854] ACPI: Power Button (FF) [PWRF]

[   44.857970] input: Power Button (CM) as /devices/virtual/input/input5

[   44.903421] ACPI: Power Button (CM) [PWRB]

[   44.903542] input: Sleep Button (CM) as /devices/virtual/input/input6

[   44.959359] ACPI: Sleep Button (CM) [SLPB]

[   44.959468] input: Lid Switch as /devices/virtual/input/input7

[   44.983456] ACPI: Lid Switch [LID]

[color=red][   45.482062] ndiswrapper: driver netathw (,01/17/2008,7.4.2.75) loaded[/color]

[   45.482593] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 17

[   45.483401] PCI: Setting latency timer of device 0000:02:00.0 to 64

[   45.926402] [fglrx] Maximum main memory to use for locked dma buffers: 1655 MBytes.

[   45.926487] [fglrx] ASYNCIO init succeed!

[   45.928697] [fglrx] PAT is enabled successfully!

[   45.940200] [fglrx] module loaded - fglrx 8.45.4 [Jan 16 2008] on minor 0

[   45.986392] sdhci: Secure Digital Host Controller Interface driver

[   45.986399] sdhci: Copyright(c) Pierre Ossman

[color=red][   46.267401] ndiswrapper: using IRQ 17[/color]

[color=red][   46.474341] wlan0: ethernet device 00:19:7d:3d:57:0e using serialized NDIS driver: netathw, version: 0x70004, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 168C:0024.5.conf[/color]

[color=red][   46.492258] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK[/color]

[   46.492481] sdhci: SDHCI controller found at 0000:08:0a.2 [1217:7120] (rev 1)

[   46.492544] ACPI: PCI Interrupt 0000:08:0a.2[A] -> GSI 21 (level, low) -> IRQ 21

[   46.492597] sdhci:slot0: Unknown controller version (16). You may experience problems.

[   46.492756] mmc0: SDHCI at 0xc0202800 irq 21 PIO

[   46.513779] usbcore: registered new interface driver ndiswrapper

[   46.594335] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:1a/LNXVIDEO:00/input/input8

[   46.652692] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)

[   46.913688] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 17

[   48.614644] NET: Registered protocol family 10

[   48.615140] lo: Disabled Privacy Extensions

[   49.374089] lp: driver loaded but no devices found

[   49.553169] Adding 2104472k swap on /dev/sda6.  Priority:-1 extents:1 across:2104472k

[   50.152004] EXT3 FS on sda7, internal journal

[   51.047557] kjournald starting.  Commit interval 5 seconds

[   51.047845] EXT3 FS on sda4, internal journal

[   51.047854] EXT3-fs: mounted filesystem with ordered data mode.

[   51.933352] ip_tables: (C) 2000-2006 Netfilter Core Team

[   52.786956] No dock devices found.

[   52.800531] ACPI: \_SB_.PCI0.IDE_.SECD.S_D0: found ejectable bay

[   52.800541] ACPI: \_SB_.PCI0.IDE_.SECD.S_D0: Adding notify handler

[   52.800602] ACPI: Bay [\_SB_.PCI0.IDE_.SECD.S_D0] Added

[   52.800611] ACPI: \_SB_.PCI0.IDE_.SECD.S_D1: found ejectable bay

[   52.800619] ACPI: \_SB_.PCI0.IDE_.SECD.S_D1: Adding notify handler

[   52.800667] ACPI: Bay [\_SB_.PCI0.IDE_.SECD.S_D1] Added

[   53.998362] apm: BIOS not found.

[   54.118479] ppdev: user-space parallel port driver

[   54.223553] audit(1212667038.907:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5192 profile="/usr/sbin/cupsd" namespace="default"

[   55.502612] eth0: link down

[   55.506774] ADDRCONF(NETDEV_UP): eth0: link is not ready

[   55.611015] Bluetooth: Core ver 2.11

[   55.611209] NET: Registered protocol family 31

[   55.611214] Bluetooth: HCI device and connection manager initialized

[   55.611222] Bluetooth: HCI socket layer initialized

[   55.676524] Bluetooth: L2CAP ver 2.9

[   55.676531] Bluetooth: L2CAP socket layer initialized

[   55.762667] Bluetooth: RFCOMM socket layer initialized

[   55.762694] Bluetooth: RFCOMM TTY layer initialized

[   55.762698] Bluetooth: RFCOMM ver 1.8

[   57.791817] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 20

[   58.811942] wlan0: no IPv6 routers present

[   59.391078] [fglrx] GART Table is not in FRAME_BUFFER range

[   59.391099] [fglrx] Reserve Block - 0 offset =  0X0 length = 0X40000

[   59.391106] [fglrx] Reserve Block - 1 offset =  0Xfff5000 length = 0Xb000

[   59.567138] [fglrx] interrupt source 10000000 successfully enabled

[   59.567144] [fglrx] enable ID = 0x00000004

[   59.567160] [fglrx] Receive enable interrupt message with irqEnableMask: 10000000

[   70.110304] hda-intel: Invalid position buffer, using LPIB read method instead.

[   73.392861] ALSA /build/buildd/linux-ubuntu-modules-2.6.24-2.6.24/debian/build/build-generic/sound/alsa-driver/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:593: hda_intel: azx_get_response timeout, switching to polling mode: last cmd=0x001f000a

[   74.395819] ALSA /build/buildd/linux-ubuntu-modules-2.6.24-2.6.24/debian/build/build-generic/sound/alsa-driver/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:600: hda_intel: azx_get_response timeout, switching to single_cmd mode: last cmd=0x001f000a

[   78.839870] CPU0 attaching NULL sched-domain.

[   78.839884] CPU1 attaching NULL sched-domain.

[   78.864181] CPU0 attaching sched-domain:

[   78.864191]  domain 0: span 03

[   78.864198]   groups: 01 02

[   78.864208] CPU1 attaching sched-domain:

[   78.864212]  domain 0: span 03

[   78.864218]   groups: 02 01

[  325.345641] CPU0 attaching NULL sched-domain.

[  325.345648] CPU1 attaching NULL sched-domain.

[  325.367743] CPU0 attaching sched-domain:

[  325.367748]  domain 0: span 03

[  325.367750]   groups: 01 02

[  325.367753]   domain 1: span 03

[  325.367755]    groups: 03

[  325.367757] CPU1 attaching sched-domain:

[  325.367759]  domain 0: span 03

[  325.367761]   groups: 02 01

[  325.367763]   domain 1: span 03

[  325.367765]    groups: 03

[  501.949135] eth0: link down

[  501.952285] ADDRCONF(NETDEV_UP): eth0: link is not ready

[  501.977303] ADDRCONF(NETDEV_UP): wlan0: link is not ready

[  503.979940] eth0: link down

[  503.984098] ADDRCONF(NETDEV_UP): eth0: link is not ready

[  504.056666] ADDRCONF(NETDEV_UP): wlan0: link is not ready

[  523.512541] NET: Registered protocol family 17

[  526.848430] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

[  544.504634] wlan0: no IPv6 routers present

[ 1272.869867] usb 3-4: new high speed USB device using ehci_hcd and address 2

[ 1273.005711] usb 3-4: configuration #1 chosen from 1 choice

[ 1273.415916] usbcore: registered new interface driver libusual

[ 1273.452267] Initializing USB Mass Storage driver...

[ 1273.454043] scsi2 : SCSI emulation for USB Mass Storage devices

[ 1273.455733] usbcore: registered new interface driver usb-storage

[ 1273.455744] USB Mass Storage support registered.

[ 1273.455930] usb-storage: device found at 2

[ 1273.455934] usb-storage: waiting for device to settle before scanning

[ 1278.448464] usb-storage: device scan complete

[ 1278.450094] scsi 2:0:0:0: Direct-Access     Lenovo   USB Flash Drive  1100 PQ: 0 ANSI: 0 CCS

[ 1278.457540] sd 2:0:0:0: [sdb] 1981440 512-byte hardware sectors (1014 MB)

[ 1278.458830] sd 2:0:0:0: [sdb] Write Protect is off

[ 1278.458838] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00

[ 1278.458843] sd 2:0:0:0: [sdb] Assuming drive cache: write through

[ 1278.462379] sd 2:0:0:0: [sdb] 1981440 512-byte hardware sectors (1014 MB)

[ 1278.463694] sd 2:0:0:0: [sdb] Write Protect is off

[ 1278.463702] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00

[ 1278.463707] sd 2:0:0:0: [sdb] Assuming drive cache: write through

[ 1278.464365]  sdb: sdb1

[ 1278.553613] sd 2:0:0:0: [sdb] Attached SCSI removable disk

[ 1278.553946] sd 2:0:0:0: Attached scsi generic sg1 type 0



再上个图:


附件:
文件注释: 啊。为什么呢
Screenshot.png
Screenshot.png [ 301.14 KiB | 被浏览 1439 次 ]



最后由 mosoplyr 编辑于 2008-06-06 12:23,总共编辑了 1 次
页首
 用户资料  
 
2 楼 
 文章标题 :
帖子发表于 : 2008-06-06 0:41 
头像

注册: 2008-03-05 12:31
帖子: 429
地址: 示爱须唱山歌
送出感谢: 0 次
接收感谢: 0 次
试试这个
http://forum.ubuntu.org.cn/viewtopic.php?t=109394


_________________
六十学裁缝,晚否......


页首
 用户资料  
 
3 楼 
 文章标题 :
帖子发表于 : 2008-06-06 12:22 

注册: 2006-08-30 16:50
帖子: 74
地址: 四川
送出感谢: 0 次
接收感谢: 0 次
谢谢楼上 我换成最新的升级软件后 就正常了
十分感谢


页首
 用户资料  
 
显示帖子 :  排序  
发表新帖 回复这个主题  [ 3 篇帖子 ] 

当前时区为 UTC + 8 小时


在线用户

正在浏览此版面的用户:没有注册用户 和 2 位游客


不能 在这个版面发表主题
不能 在这个版面回复主题
不能 在这个版面编辑帖子
不能 在这个版面删除帖子
不能 在这个版面提交附件

前往 :  
本站点为公益性站点,用于推广开源自由软件,由 DiaHosting VPSBudgetVM VPS 提供服务。
我们认为:软件应可免费取得,软件工具在各种语言环境下皆可使用,且不会有任何功能上的差异;
人们应有定制和修改软件的自由,且方式不受限制,只要他们自认为合适。

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
简体中文语系由 王笑宇 翻译