当前时区为 UTC + 8 小时



发表新帖 回复这个主题  [ 1 篇帖子 ] 
作者 内容
1 楼 
 文章标题 : 关于网卡驱动怎么安装的问题,请教大家,谢谢!
帖子发表于 : 2011-04-11 19:50 

注册: 2010-11-02 18:14
帖子: 14
送出感谢: 0 次
接收感谢: 0 次
我先说下我的问题。
我通过virtualbox在虚拟机中把ubuntu10.04安装到U盘,然后在笔记本上从U盘启动,顺利进入系统,但是系统提示没有安装网卡驱动。我按照我的网卡型号下载了对应的驱动,但是不会安装,所以请各位看看怎么安装这个驱动,尽量详细点,我刚用ubuntu没几天,非常感谢!!!
网卡:Realtek RTL8102E/8103E系列 PCI-E 快速以太网 NIC(NDIS 6.20)

我附上我下载的那个网卡驱动。

下面是下载的网卡驱动包里面的readme文件。

<Linux device driver for Realtek Ethernet controllers>

This is the Linux device driver released for RealTek RTL8101E, RTL8102E(L) and RTL8103E(L), the Fast Ethernet controller with PCI-Express interface.

<Requirements>

- kernel source tree (supported Linux kernel 2.6.x and 2.4.x)
- For linux kernel 2.4.x, this driver supports linux kernel 2.4.20 and latter.
- compiler/binutils for kernel compilation

<Quick install with proper kernel settings>
Check whether the built-in driver, r8169.ko (or r8169.o for kernel 2.4.x), is installed.
# lsmod | grep r8169

If it is installed, please remove it.
# rmmod r8169
note: If the built-in driver cannot removed by rmmod, please edit /etc/modprobe.conf and comment 'alias eth0 r8169'. Then, remmove it again or reboot your computer.

Unpack the tarball :
# tar vjxf r8101-1.aaa.bb.tar.bz2

Change to the directory:
# cd r8101-1.aaa.bb

If you are running the target kernel, then you should be able to do :

# make clean modules (as root or with sudo)
# make install
# depmod -a
# modprobe r8101

You can check whether the driver is loaded by using following commands.

# lsmod | grep r8101
# ifconfig -a

If there is a device name, ethX, shown on the monitor, the linux
driver is loaded. Then, you can use the following command to activate
the ethX.

# ifconfig ethX

,where X=0,1,2,...


<Set the network related information>
1. Set manually
a. Set the IP address of your machine.

# ifconfig ethX "the IP address of your machine"

b. Set the IP address of DNS.

Insert the following configuration in /etc/resolv.conf.

nameserver "the IP address of DNS"

c. Set the IP address of gateway.

# route add default gw "the IP address of gateway"

2. Set by doing configurations in /etc/sysconfig/network-scripts
/ifcfg-ethX for Redhat and Fedora, or /etc/sysconfig/network
/ifcfg-ethX for SuSE. There are two examples to set network
configurations.

a. Fixed IP address:
DEVICE=eth0
BOOTPROTO=static
ONBOOT=yes
TYPE=ethernet
NETMASK=255.255.255.0
IPADDR=192.168.1.1
GATEWAY=192.168.1.254
BROADCAST=192.168.1.255

b. DHCP:
DEVICE=eth0
BOOTPROTO=dhcp
ONBOOT=yes

<Modify the MAC address>
There are two ways to modify the MAC address of the NIC.
1. Use ifconfig:

# ifconfig ethX hw ether YY:YY:YY:YY:YY:YY

,where X is the device number assigned by Linux kernel, and
YY:YY:YY:YY:YY:YY is the MAC address assigned by the user.

2. Use ip:

# ip link set ethX address YY:YY:YY:YY:YY:YY

,where X is the device number assigned by Linux kernel, and
YY:YY:YY:YY:YY:YY is the MAC address assigned by the user.

<Force Link Status>

1. Force the link status when insert the driver.

If the user is in the path ~/r8101, the link status can be forced
to one of the 4 modes as following command.

# insmod ./src/r8101.ko speed=SPEED_MODE duplex=DUPLEX_MODE autoneg=NWAY_OPTION

,where
SPEED_MODE = 100 for 100Mbps
= 10 for 10Mbps
DUPLEX_MODE = 0 for half-duplex
= 1 for full-duplex
NWAY_OPTION = 0 for auto-negotiation off (true force)
= 1 for auto-negotiation on (nway force)
For example:

# insmod ./src/r8101.ko speed=100 duplex=0 autoneg=1

will force PHY to operate in 100Mpbs Half-duplex(nway force).

2. Force the link status by using ethtool.
a. Insert the driver first.
b. Make sure that ethtool exists in /sbin.
c. Force the link status as the following command.

# ethtool -s ethX speed SPEED_MODE duplex DUPLEX_MODE autoneg NWAY_OPTION

,where
SPEED_MODE = 100 for 100Mbps
= 10 for 10Mbps
DUPLEX_MODE = half for half-duplex
= full for full-duplex
NWAY_OPTION = off for auto-negotiation off (true force)
= on for auto-negotiation on (nway force)

For example:

# ethtool -s eth0 speed 100 duplex full autoneg on

will force PHY to operate in 100Mpbs Full-duplex(nway force).

<Jumbo Frame>
RTL8101E, RTL8102E and RTL8103E do not support Jumbo Frame.


附件:
文件注释: 这个是驱动,向大家请教了,谢谢!
realtek_rtl8100e_101300_linux.zip [42.82 KiB]
被下载 855 次
页首
 用户资料  
 
显示帖子 :  排序  
发表新帖 回复这个主题  [ 1 篇帖子 ] 

当前时区为 UTC + 8 小时


在线用户

正在浏览此版面的用户:没有注册用户 和 2 位游客


不能 在这个版面发表主题
不能 在这个版面回复主题
不能 在这个版面编辑帖子
不能 在这个版面删除帖子
不能 在这个版面提交附件

前往 :  
本站点为公益性站点,用于推广开源自由软件,由 DiaHosting VPSBudgetVM VPS 提供服务。
我们认为:软件应可免费取得,软件工具在各种语言环境下皆可使用,且不会有任何功能上的差异;
人们应有定制和修改软件的自由,且方式不受限制,只要他们自认为合适。

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
简体中文语系由 王笑宇 翻译