当前时区为 UTC + 8 小时



发表新帖 回复这个主题  [ 2 篇帖子 ] 
作者 内容
1 楼 
 文章标题 : [问题]ACER4520G本本安装ubuntu7.10-amd64出现的几个问题
帖子发表于 : 2007-09-10 18:14 

注册: 2006-11-20 20:08
帖子: 9
送出感谢: 0 次
接收感谢: 0 次
显卡是G8400mgs的系统没带驱动,不能进入X下,到nvidia网站上下载NVIDIA-Linux-x86_64-100.14.09-pkg2.run安装后才行
在启动的时候,会随机的进入不了按重启几次才行
NTFS分区中文不能显示,必须把NTFS-3G设置为能写才行。
声卡和无线网卡驱动不了
从alsa下了1.04安装后声卡还是不行,我的声卡在windowsXP显卡为reltekHD的,为什么在alsa驱动设置 alsaconf中检测为intel_HD的呢?
无线网卡为Atheros5007EG但用ndiswrapper-1.47编译其XP的驱动后仍发现不了他,疑为32位的驱动不被64位系统支持。
求高手帮我解决一下。


lspci显示:
*************************************
00:00.0 RAM memory: nVidia Corporation Unknown device 0547 (rev a2)
00:01.0 ISA bridge: nVidia Corporation Unknown device 0548 (rev a2)
00:01.1 SMBus: nVidia Corporation Unknown device 0542 (rev a2)
00:01.2 RAM memory: nVidia Corporation Unknown device 0541 (rev a2)
00:01.3 Co-processor: nVidia Corporation Unknown device 0543 (rev a2)
00:02.0 USB Controller: nVidia Corporation Unknown device 055e (rev a2)
00:02.1 USB Controller: nVidia Corporation Unknown device 055f (rev a2)
00:04.0 USB Controller: nVidia Corporation Unknown device 055e (rev a2)
00:04.1 USB Controller: nVidia Corporation Unknown device 055f (rev a2)
00:06.0 IDE interface: nVidia Corporation Unknown device 0560 (rev a1)
00:07.0 Audio device: nVidia Corporation Unknown device 055c (rev a1)
00:08.0 PCI bridge: nVidia Corporation Unknown device 0561 (rev a2)
00:09.0 IDE interface: nVidia Corporation Unknown device 0550 (rev a2)
00:0a.0 Ethernet controller: nVidia Corporation Unknown device 054c (rev a2)
00:0b.0 PCI bridge: nVidia Corporation Unknown device 0562 (rev a2)
00:0c.0 PCI bridge: nVidia Corporation Unknown device 0563 (rev a2)
00:0e.0 PCI bridge: nVidia Corporation Unknown device 0563 (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:09.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832 (rev 05)
01:09.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)
01:09.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 12)
01:09.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
01:09.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12)
02:00.0 VGA compatible controller: nVidia Corporation Unknown device 0428 (rev a1)
07:00.0 Ethernet controller: Atheros Communications, Inc. Unknown device 001c (rev 01)
***************************************************


demsg显示:
[ 0.000000] Linux version 2.6.22-11-generic (buildd@yellow) (gcc version 4.1.3 20070831 (prerelease) (Ubuntu 4.1.2-16ubuntu1)) #1 SMP Fri Sep 7 04:31:16 GMT 2007 (Ubuntu 2.6.22-11.32-generic)
[ 0.000000] Command line: root=UUID=056caacf-5ffe-4157-a9dd-cd7b14797636 ro quiet splash
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
[ 0.000000] BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fed0000 (usable)
[ 0.000000] BIOS-e820: 000000007fed0000 - 000000007fee5000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fee5000 - 000000007fee6000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fee6000 - 000000007ff00000 (reserved)
[ 0.000000] BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] Entering add_active_range(0, 0, 158) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 523984) 1 entries of 3200 used
[ 0.000000] end_pfn_map = 1048576
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F7E30, 0024 (r2 PTLTD )
[ 0.000000] ACPI: XSDT 7FEDE2C7, 006C (r1 ACRSYS ACRPRDCT 6040000 LTP 0)
[ 0.000000] ACPI: FACP 7FEE492A, 00F4 (r3 NVIDIA MCP67-M 6040000 PTL_ F4240)
[ 0.000000] ACPI: DSDT 7FEDE333, 6583 (r1 NVIDIA MCP67 6040000 MSFT 3000000)
[ 0.000000] ACPI: FACS 7FEE5FC0, 0040
[ 0.000000] ACPI: SRAT 7FEE4A1E, 00A0 (r1 AMD HAMMER 6040000 AMD 1)
[ 0.000000] ACPI: WDAT 7FEE4ABE, 0104 (r1 PTLTD WDATTBL 6040000 LTP 1)
[ 0.000000] ACPI: SSDT 7FEE4BC2, 01C4 (r1 PTLTD POWERNOW 6040000 LTP 1)
[ 0.000000] ACPI: MCFG 7FEE4D86, 003C (r1 PTLTD MCFG 6040000 LTP 0)
[ 0.000000] ACPI: HPET 7FEE4DC2, 0038 (r1 PTLTD HPETTBL 6040000 LTP 1)
[ 0.000000] ACPI: APIC 7FEE4DFA, 0068 (r1 PTLTD APIC 6040000 LTP 0)
[ 0.000000] ACPI: BOOT 7FEE4E62, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
[ 0.000000] ACPI: SLIC 7FEE4E8A, 0176 (r1 ACRSYS ACRPRDCT 6040000 acer 0)
[ 0.000000] SRAT: PXM 0 -> APIC 0 -> Node 0
[ 0.000000] SRAT: PXM 0 -> APIC 1 -> Node 0
[ 0.000000] SRAT: Node 0 PXM 0 0-a0000
[ 0.000000] Entering add_active_range(0, 0, 158) 0 entries of 3200 used
[ 0.000000] SRAT: Node 0 PXM 0 0-80000000
[ 0.000000] Entering add_active_range(0, 0, 158) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 523984) 1 entries of 3200 used
[ 0.000000] NUMA: Using 63 for the hash shift.
[ 0.000000] Bootmem setup node 0 0000000000000000-000000007fed0000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0 -> 158
[ 0.000000] 0: 256 -> 523984
[ 0.000000] On node 0 totalpages: 523886
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1127 pages reserved
[ 0.000000] DMA zone: 2815 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7107 pages used for memmap
[ 0.000000] DMA32 zone: 512781 pages, LIFO batch:31
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000d0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 34696 bytes of per cpu data
[ 0.000000] Built 1 zonelists. Total pages: 515596
[ 0.000000] Kernel command line: root=UUID=056caacf-5ffe-4157-a9dd-cd7b14797636 ro quiet splash
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Marking TSC unstable due to TSCs unsynchronized
[ 15.324992] time.c: Detected 1700.159 MHz processor.
[ 15.327135] Console: colour VGA+ 80x25
[ 15.327155] Checking aperture...
[ 15.327159] CPU 0: aperture @ 46000000 size 32 MB
[ 15.327161] Aperture too small (32 MB)
[ 15.333488] No AGP bridge found
[ 15.353703] Memory: 2054932k/2095936k available (2278k kernel code, 40612k reserved, 1185k data, 300k init)
[ 15.353754] SLUB: Genslabs=23, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 15.430121] Calibrating delay using timer specific routine.. 3403.77 BogoMIPS (lpj=6807544)
[ 15.430156] Security Framework v1.0.0 initialized
[ 15.430163] SELinux: Disabled at boot.
[ 15.430360] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 15.431574] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 15.432151] Mount-cache hash table entries: 256
[ 15.432295] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 15.432298] CPU: L2 Cache: 256K (64 bytes/line)
[ 15.432301] CPU 0/0 -> Node 0
[ 15.432303] CPU: Physical Processor ID: 0
[ 15.432305] CPU: Processor Core ID: 0
[ 15.432325] SMP alternatives: switching to UP code
[ 15.432587] Early unpacking initramfs... done
[ 15.778628] ACPI: Core revision 20070126
[ 15.778706] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 16.229306] Using local APIC timer interrupts.
[ 16.288100] result 12501162
[ 16.288102] Detected 12.501 MHz APIC timer.
[ 16.289766] SMP alternatives: switching to SMP code
[ 16.289908] Booting processor 1/2 APIC 0x1
[ 16.300513] Initializing CPU#1
[ 16.378181] Calibrating delay using timer specific routine.. 3400.56 BogoMIPS (lpj=6801126)
[ 16.378190] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 16.378192] CPU: L2 Cache: 256K (64 bytes/line)
[ 16.378195] CPU 1/1 -> Node 0
[ 16.378197] CPU: Physical Processor ID: 0
[ 16.378199] CPU: Processor Core ID: 1
[ 16.378281] AMD Athlon(tm) 64 X2 Dual-Core Processor TK-53 stepping 01
[ 16.381661] Brought up 2 CPUs
[ 16.391108] migration_cost=51
[ 16.390787] NET: Registered protocol family 16
[ 16.390888] ACPI: bus type pci registered
[ 16.390894] PCI: Using configuration type 1
[ 16.391996] ACPI: EC: Look up EC in DSDT
[ 16.392914] ACPI: EC: GPE=0x10, ports=0x66, 0x62
[ 18.894083] ACPI: Interpreter enabled
[ 18.894087] ACPI: (supports S0 S3 S4 S5)
[ 18.894107] ACPI: Using IOAPIC for interrupt routing
[ 18.901931] ACPI: EC: GPE=0x10, ports=0x66, 0x62
[ 18.901995] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 18.902002] PCI: Probing PCI hardware (bus 00)
[ 18.902861] PCI: Transparent bridge - 0000:00:08.0
[ 18.903169] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 18.903266] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[ 18.903287] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
[ 18.903321] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
[ 18.903354] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR3._PRT]
[ 18.934502] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 *10 11 14 15)
[ 18.934725] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 10 *11 14 15)
[ 18.934939] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 10 11 14 15) *0, disabled.
[ 18.935153] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 10 11 14 15) *0, disabled.
[ 18.935373] ACPI: PCI Interrupt Link [LK1E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 18.935588] ACPI: PCI Interrupt Link [LK2E] (IRQs 16 17 18 19 20 21 22 23) *10
[ 18.935801] ACPI: PCI Interrupt Link [LK3E] (IRQs 16 17 18 19 20 21 22 23) *10
[ 18.936014] ACPI: PCI Interrupt Link [LK4E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 18.936234] ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20 21 22 23) *10
[ 18.936454] ACPI: PCI Interrupt Link [LUS0] (IRQs 16 17 18 19 20 21 22 23) *11
[ 18.936675] ACPI: PCI Interrupt Link [LUS2] (IRQs 16 17 18 19 20 21 22 23) *10
[ 18.936901] ACPI: PCI Interrupt Link [LMAC] (IRQs 16 17 18 19 20 21 22 23) *11
[ 18.937121] ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 20 21 22 23) *10
[ 18.937342] ACPI: PCI Interrupt Link [LGPU] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 18.937556] ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 18.937769] ACPI: PCI Interrupt Link [LSI0] (IRQs 16 17 18 19 20 21 22 23) *5
[ 18.937989] ACPI: PCI Interrupt Link [Z002] (IRQs 16 17 18 19 20 21 22 23) *7
[ 18.938208] ACPI: PCI Interrupt Link [Z003] (IRQs 16 17 18 19 20 21 22 23) *11
[ 18.938423] ACPI: PCI Interrupt Link [LPMU] (IRQs 16 17 18 19 20 21 22 23) *11
[ 18.938557] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 18.938574] pnp: PnP ACPI init
[ 18.938587] ACPI: bus type pnp registered
[ 18.941627] pnp: PnP ACPI: found 13 devices
[ 18.941630] ACPI: ACPI bus type pnp unregistered
[ 18.941702] PCI: Using ACPI for IRQ routing
[ 18.941706] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 18.941714] PCI: Cannot allocate resource region 7 of bridge 0000:00:0c.0
[ 18.941781] PCI: Cannot allocate resource region 8 of bridge 0000:00:0c.0
[ 18.941843] PCI: Cannot allocate resource region 9 of bridge 0000:00:0c.0
[ 18.942005] NET: Registered protocol family 8
[ 18.942008] NET: Registered protocol family 20
[ 18.942097] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 18.942102] hpet0: 3 32-bit timers, 25000000 Hz
[ 18.943173] pnp: 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
[ 18.943179] pnp: 00:03: ioport range 0x1000-0x107f has been reserved
[ 18.943183] pnp: 00:03: ioport range 0x1080-0x10ff has been reserved
[ 18.943186] pnp: 00:03: ioport range 0x1400-0x147f has been reserved
[ 18.943190] pnp: 00:03: ioport range 0x1480-0x14ff has been reserved
[ 18.943193] pnp: 00:03: ioport range 0x1800-0x187f has been reserved
[ 18.943202] pnp: 00:03: ioport range 0x1880-0x18ff has been reserved
[ 18.943206] pnp: 00:03: ioport range 0x3040-0x307f has been reserved
[ 18.943209] pnp: 00:03: ioport range 0x3000-0x303f has been reserved
[ 18.943223] pnp: 00:0b: iomem range 0xffc00000-0xffffffff could not be reserved
[ 18.943227] pnp: 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 18.943239] pnp: 00:0b: iomem range 0xfee00000-0xfeefffff could not be reserved
[ 18.943243] pnp: 00:0b: iomem range 0xfed00000-0xfed00fff has been reserved
[ 18.943611] PCI: Bridge: 0000:00:08.0
[ 18.943613] IO window: disabled.
[ 18.943618] MEM window: f2100000-f21fffff
[ 18.943621] PREFETCH window: disabled.
[ 18.943628] PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:02:00.0
[ 18.943693] PCI: Bridge: 0000:00:0b.0
[ 18.943695] IO window: 4000-4fff
[ 18.943699] MEM window: cc000000-ceffffff
[ 18.943702] PREFETCH window: d0000000-dfffffff
[ 18.943705] PCI: Bridge: 0000:00:0c.0
[ 18.943707] IO window: disabled.
[ 18.943709] MEM window: disabled.
[ 18.943711] PREFETCH window: disabled.
[ 18.943714] PCI: Bridge: 0000:00:0e.0
[ 18.943716] IO window: disabled.
[ 18.943719] MEM window: f2000000-f20fffff
[ 18.943722] PREFETCH window: disabled.
[ 18.943733] PCI: Setting latency timer of device 0000:00:08.0 to 64
[ 18.943742] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 18.943749] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 18.943757] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 18.943817] NET: Registered protocol family 2
[ 18.944845] Time: hpet clocksource has been installed.
[ 18.996209] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 18.997162] TCP established hash table entries: 262144 (order: 10, 6291456 bytes)
[ 19.000559] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 19.001132] TCP: Hash tables configured (established 262144 bind 65536)
[ 19.001136] TCP reno registered
[ 19.016499] checking if image is initramfs... it is
[ 19.694465] Freeing initrd memory: 7253k freed
[ 19.698684] Simple Boot Flag at 0x36 set to 0x1
[ 19.699368] audit: initializing netlink socket (disabled)
[ 19.699381] audit(1189420779.912:1): initialized
[ 19.701866] VFS: Disk quotas dquot_6.5.1
[ 19.701929] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 19.702044] io scheduler noop registered
[ 19.702046] io scheduler anticipatory registered
[ 19.702049] io scheduler deadline registered
[ 19.702156] io scheduler cfq registered (default)
[ 19.703033] Boot video device is 0000:02:00.0
[ 19.703214] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 19.703238] assign_interrupt_mode Found MSI capability
[ 19.703259] Allocate Port Service[0000:00:0b.0:pcie00]
[ 19.703336] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 19.703359] assign_interrupt_mode Found MSI capability
[ 19.703375] Allocate Port Service[0000:00:0c.0:pcie00]
[ 19.703449] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 19.703471] assign_interrupt_mode Found MSI capability
[ 19.703488] Allocate Port Service[0000:00:0e.0:pcie00]
[ 19.735216] Real Time Clock Driver v1.12ac
[ 19.735415] hpet_resources: 0xfed00000 is busy
[ 19.735447] Linux agpgart interface v0.102 (c) Dave Jones
[ 19.735450] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 19.736905] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 19.737058] input: Macintosh mouse button emulation as /class/input/input0
[ 19.737150] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 19.739814] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 19.739819] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 19.740040] mice: PS/2 mouse device common for all mice
[ 19.740585] TCP cubic registered
[ 19.740654] NET: Registered protocol family 1
[ 19.740903] /build/buildd/linux-source-2.6.22-2.6.22/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 19.740915] Freeing unused kernel memory: 300k freed
[ 19.768311] input: AT Translated Set 2 keyboard as /class/input/input1
[ 20.983907] AppArmor: AppArmor initialized<5>audit(1189420781.200:2): info="AppArmor initialized" pid=1264
[ 20.994206] fuse init (API version 7.8)
[ 21.000771] Failure registering capabilities with primary security module.
[ 21.055417] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 21.055424] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 21.055449] ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 21.055462] ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 21.072041] ACPI: Thermal Zone [THRM] (55 C)
[ 21.874995] usbcore: registered new interface driver usbfs
[ 21.875027] usbcore: registered new interface driver hub
[ 21.875053] usbcore: registered new device driver usb
[ 21.875982] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 21.876391] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 23
[ 21.876402] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 23 (level, low) -> IRQ 23
[ 21.876535] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 21.876543] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 21.876733] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 21.876754] ohci_hcd 0000:00:02.0: irq 23, io mem 0xf2486000
[ 21.883483] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
[ 21.888127] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 21.888134] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 21.927246] SCSI subsystem initialized
[ 21.937690] usb usb1: configuration #1 chosen from 1 choice
[ 21.937727] hub 1-0:1.0: USB hub found
[ 21.937738] hub 1-0:1.0: 4 ports detected
[ 21.954692] libata version 2.21 loaded.
[ 22.043426] ACPI: PCI Interrupt Link [Z002] enabled at IRQ 22
[ 22.043439] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [Z002] -> GSI 22 (level, low) -> IRQ 22
[ 22.043573] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 22.043582] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 22.043650] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
[ 22.043672] ohci_hcd 0000:00:04.0: irq 22, io mem 0xf2487000
[ 22.105052] usb usb2: configuration #1 chosen from 1 choice
[ 22.105090] hub 2-0:1.0: USB hub found
[ 22.105109] hub 2-0:1.0: 4 ports detected
[ 22.206977] NFORCE-MCP67: IDE controller at PCI slot 0000:00:06.0
[ 22.207001] NFORCE-MCP67: chipset revision 161
[ 22.207004] NFORCE-MCP67: not 100% native mode: will probe irqs later
[ 22.207009] NFORCE-MCP67: BIOS didn't set cable bits correctly. Enabling workaround.
[ 22.207015] NFORCE-MCP67: 0000:00:06.0 (rev a1) UDMA133 controller
[ 22.207025] ide0: BM-DMA at 0x30c0-0x30c7, BIOS settings: hda:DMA, hdb:pio
[ 22.207037] Probing IDE interface ide0...
[ 22.345367] usb 1-2: new low speed USB device using ohci_hcd and address 2
[ 22.546355] usb 1-2: configuration #1 chosen from 1 choice
[ 22.942524] hda: Optiarc CD-RW CRX880A, ATAPI CD/DVD-ROM drive
[ 23.614679] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 23.618535] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10
[ 23.618547] ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> IRQ 10
[ 23.672187] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[f2100000-f21007ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 23.676729] ahci 0000:00:09.0: version 2.2
[ 23.677121] ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 21
[ 23.677133] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LSI0] -> GSI 21 (level, low) -> IRQ 21
[ 23.679033] usbcore: registered new interface driver hiddev
[ 23.685696] hda: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 23.685709] Uniform CD-ROM driver Revision: 3.20
[ 23.687829] input: USB Mouse as /class/input/input2
[ 23.688054] input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:02.0-2
[ 23.688071] usbcore: registered new interface driver usbhid
[ 23.688076] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 24.681598] ahci 0000:00:09.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode
[ 24.681604] ahci 0000:00:09.0: flags: 64bit led clo pmp pio slum part
[ 24.681609] PCI: Setting latency timer of device 0000:00:09.0 to 64
[ 24.682034] scsi0 : ahci
[ 24.682104] scsi1 : ahci
[ 24.682160] scsi2 : ahci
[ 24.682215] scsi3 : ahci
[ 24.682296] ata1: SATA max UDMA/133 cmd 0xffffc20000ab0100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 508
[ 24.682301] ata2: SATA max UDMA/133 cmd 0xffffc20000ab0180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 508
[ 24.682306] ata3: SATA max UDMA/133 cmd 0xffffc20000ab0200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 508
[ 24.682310] ata4: SATA max UDMA/133 cmd 0xffffc20000ab0280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 508
[ 24.945975] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00241b00d5552b00]
[ 25.165325] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 25.166639] ata1.00: ATA-7: Hitachi HTS541680J9SA00, SB2OC70P, max UDMA/100
[ 25.166645] ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 25.167684] ata1.00: configured for UDMA/100
[ 25.477172] ata2: SATA link down (SStatus 0 SControl 300)
[ 25.789004] ata3: SATA link down (SStatus 0 SControl 300)
[ 26.100852] ata4: SATA link down (SStatus 0 SControl 300)
[ 26.101359] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54168 SB2O PQ: 0 ANSI: 5
[ 26.101986] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 20
[ 26.101999] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 20 (level, low) -> IRQ 20
[ 26.102134] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 26.102142] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 26.102206] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
[ 26.102247] ehci_hcd 0000:00:02.1: debug port 1
[ 26.102251] PCI: cache line size of 64 is not supported by device 0000:00:02.1
[ 26.102266] ehci_hcd 0000:00:02.1: irq 20, io mem 0xf2489000
[ 26.102274] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 26.102314] usb 1-2: USB disconnect, address 2
[ 26.102676] usb usb3: configuration #1 chosen from 1 choice
[ 26.102704] hub 3-0:1.0: USB hub found
[ 26.102711] hub 3-0:1.0: 4 ports detected
[ 26.117121] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 26.117137] sd 0:0:0:0: [sda] Write Protect is off
[ 26.117140] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 26.117157] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 26.117216] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 26.117226] sd 0:0:0:0: [sda] Write Protect is off
[ 26.117229] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 26.117244] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 26.117250] sda:ACPI: PCI Interrupt Link [Z003] enabled at IRQ 19
[ 26.206441] ACPI: PCI Interrupt 0000:00:04.1[B] -> Link [Z003] -> GSI 19 (level, low) -> IRQ 19
[ 26.206576] PCI: Setting latency timer of device 0000:00:04.1 to 64
[ 26.206584] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 26.206643] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 4
[ 26.206682] ehci_hcd 0000:00:04.1: debug port 1
[ 26.206686] PCI: cache line size of 64 is not supported by device 0000:00:04.1
[ 26.206700] ehci_hcd 0000:00:04.1: irq 19, io mem 0xf2489400
[ 26.206708] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 26.206820] usb usb4: configuration #1 chosen from 1 choice
[ 26.206854] hub 4-0:1.0: USB hub found
[ 26.206862] hub 4-0:1.0: 4 ports detected
[ 26.312288] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 18
[ 26.312301] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LMAC] -> GSI 18 (level, low) -> IRQ 18
[ 26.312309] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 26.312320] forcedeth: using HIGHDMA
[ 26.312343] 0000:00:0a.0: Invalid Mac address detected: 39:a5:55:24:1b:00
[ 26.312347] Please complain to your hardware vendor. Switching to a random MAC.
[ 26.501287] sda1 sda2 < sda5 sda6 sda7 sda8 sda9 >
[ 26.586372] sd 0:0:0:0: [sda] Attached SCSI disk
[ 26.591737] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 26.717017] usb 1-2: new low speed USB device using ohci_hcd and address 3
[ 26.831102] eth0: forcedeth.c: subsystem: 01025:0127 bound to 0000:00:0a.0
[ 26.934077] usb 1-2: configuration #1 chosen from 1 choice
[ 26.944155] input: USB Mouse as /class/input/input3
[ 26.944179] input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:02.0-2
[ 27.065714] Attempting manual resume
[ 27.065719] swsusp: Resume From Partition 8:8
[ 27.065721] PM: Checking swsusp image.
[ 27.065893] PM: Resume from disk failed.
[ 27.107053] kjournald starting. Commit interval 5 seconds
[ 27.107425] EXT3-fs: mounted filesystem with ordered data mode.
[ 40.348891] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 40.354387] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 40.657922] input: PC Speaker as /class/input/input4
[ 40.692594] sdhci: Secure Digital Host Controller Interface driver
[ 40.692600] sdhci: Copyright(c) Pierre Ossman
[ 40.692659] sdhci: SDHCI controller found at 0000:01:09.1 [1180:0822] (rev 22)
[ 40.693049] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 11
[ 40.693062] ACPI: PCI Interrupt 0000:01:09.1[B] -> Link [LNK2] -> GSI 11 (level, low) -> IRQ 11
[ 40.693359] mmc0: SDHCI at 0xf2100800 irq 11 DMA
[ 40.949300] ndiswrapper version 1.45 loaded (smp=yes)
[ 41.156203] ndiswrapper (check_nt_hdr:153): kernel is 64-bit, but Windows driver is not 64-bit;bad magic: 010B
[ 41.156211] ndiswrapper (load_sys_files:216): couldn't prepare driver 'net5211'
[ 41.156726] ndiswrapper (load_wrap_driver:118): couldn't load driver net5211; check system log for messages from 'loadndisdriver'
[ 41.156793] usbcore: registered new interface driver ndiswrapper
[ 41.460865] ACPI: PCI Interrupt Link [LK2E] enabled at IRQ 17
[ 41.460878] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LK2E] -> GSI 17 (level, low) -> IRQ 17
[ 41.460888] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 41.462128] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 100.14.11 Wed Jun 13 16:33:22 PDT 2007
[ 41.586906] Synaptics Touchpad, model: 1, fw: 6.5, id: 0x81a0b1, caps: 0xa04711/0xa04000
[ 41.622162] input: SynPS/2 Synaptics TouchPad as /class/input/input5
[ 42.061449] snd_hda_intel: disagrees about version of symbol snd_ctl_add
[ 42.061455] snd_hda_intel: Unknown symbol snd_ctl_add
[ 42.061597] snd_hda_intel: disagrees about version of symbol snd_card_register
[ 42.061600] snd_hda_intel: Unknown symbol snd_card_register
[ 42.061640] snd_hda_intel: disagrees about version of symbol snd_card_free
[ 42.061643] snd_hda_intel: Unknown symbol snd_card_free
[ 42.061721] snd_hda_intel: disagrees about version of symbol snd_card_proc_new
[ 42.061724] snd_hda_intel: Unknown symbol snd_card_proc_new
[ 42.061847] snd_hda_intel: disagrees about version of symbol snd_ctl_find_id
[ 42.061849] snd_hda_intel: Unknown symbol snd_ctl_find_id
[ 42.061946] snd_hda_intel: disagrees about version of symbol snd_ctl_new1
[ 42.061948] snd_hda_intel: Unknown symbol snd_ctl_new1
[ 42.062033] snd_hda_intel: disagrees about version of symbol snd_component_add
[ 42.062035] snd_hda_intel: Unknown symbol snd_component_add
[ 42.062084] snd_hda_intel: disagrees about version of symbol snd_card_new
[ 42.062086] snd_hda_intel: Unknown symbol snd_card_new
[ 42.062293] snd_hda_intel: disagrees about version of symbol snd_ctl_elem_read
[ 42.062295] snd_hda_intel: Unknown symbol snd_ctl_elem_read
[ 42.062341] snd_hda_intel: disagrees about version of symbol snd_ctl_elem_write
[ 42.062344] snd_hda_intel: Unknown symbol snd_ctl_elem_write
[ 42.062473] snd_hda_intel: disagrees about version of symbol snd_device_new
[ 42.062475] snd_hda_intel: Unknown symbol snd_device_new
[ 42.062580] snd_hda_intel: disagrees about version of symbol snd_card_disconnect
[ 42.062583] snd_hda_intel: Unknown symbol snd_card_disconnect
[ 42.065860] snd_hda_intel: disagrees about version of symbol snd_ctl_add
[ 42.065867] snd_hda_intel: Unknown symbol snd_ctl_add
[ 42.066007] snd_hda_intel: disagrees about version of symbol snd_card_register
[ 42.066010] snd_hda_intel: Unknown symbol snd_card_register
[ 42.066050] snd_hda_intel: disagrees about version of symbol snd_card_free
[ 42.066053] snd_hda_intel: Unknown symbol snd_card_free
[ 42.066130] snd_hda_intel: disagrees about version of symbol snd_card_proc_new
[ 42.066133] snd_hda_intel: Unknown symbol snd_card_proc_new
[ 42.066255] snd_hda_intel: disagrees about version of symbol snd_ctl_find_id
[ 42.066258] snd_hda_intel: Unknown symbol snd_ctl_find_id
[ 42.066354] snd_hda_intel: disagrees about version of symbol snd_ctl_new1
[ 42.066357] snd_hda_intel: Unknown symbol snd_ctl_new1
[ 42.066441] snd_hda_intel: disagrees about version of symbol snd_component_add
[ 42.066444] snd_hda_intel: Unknown symbol snd_component_add
[ 42.066491] snd_hda_intel: disagrees about version of symbol snd_card_new
[ 42.066494] snd_hda_intel: Unknown symbol snd_card_new
[ 42.066700] snd_hda_intel: disagrees about version of symbol snd_ctl_elem_read
[ 42.066703] snd_hda_intel: Unknown symbol snd_ctl_elem_read
[ 42.066749] snd_hda_intel: disagrees about version of symbol snd_ctl_elem_write
[ 42.066752] snd_hda_intel: Unknown symbol snd_ctl_elem_write
[ 42.066880] snd_hda_intel: disagrees about version of symbol snd_device_new
[ 42.066883] snd_hda_intel: Unknown symbol snd_device_new
[ 42.066987] snd_hda_intel: disagrees about version of symbol snd_card_disconnect
[ 42.066990] snd_hda_intel: Unknown symbol snd_card_disconnect
[ 43.164283] lp: driver loaded but no devices found
[ 43.321207] Adding 1951856k swap on /dev/sda8. Priority:-1 extents:1 across:1951856k
[ 44.029070] EXT3 FS on sda9, internal journal
[ 45.928745] audit(1189392006.918:3): operation="profile_load" info="failed to unpack profile" name="/usr/lib/cups/backend/cups-pdf" pid=4461
[ 47.311292] NET: Registered protocol family 17
[ 47.738016] ACPI: Battery Slot [BAT1] (battery present)
[ 47.992815] No dock devices found.
[ 48.034470] ACPI: AC Adapter [ACAD] (on-line)
[ 48.109124] input: Power Button (FF) as /class/input/input6
[ 48.109150] ACPI: Power Button (FF) [PWRF]
[ 48.109209] input: Power Button (CM) as /class/input/input7
[ 48.109227] ACPI: Power Button (CM) [PWRB]
[ 48.109326] input: Lid Switch as /class/input/input8
[ 48.109350] ACPI: Lid Switch [LID]
[ 48.109395] input: Sleep Button (CM) as /class/input/input9
[ 48.109412] ACPI: Sleep Button (CM) [SLPB]
[ 48.717883] set_level status: 0
[ 48.718106] ACPI: Video Device [IGPU] (multi-head: yes rom: no post: no)
[ 49.217734] set_level status: 0
[ 49.217944] ACPI: Video Device [Z004] (multi-head: yes rom: no post: no)
[ 49.563655] powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual-Core Processor TK-53 processors (version 2.00.00)
[ 49.563790] powernow-k8: 0 : fid 0x9 (1700 MHz), vid 0x13
[ 49.563796] powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x14
[ 49.563799] powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x1a
[ 54.874290] ppdev: user-space parallel port driver
[ 55.929380] Failure registering capabilities with primary security module.
[ 56.225859] Bluetooth: Core ver 2.11
[ 56.226010] NET: Registered protocol family 31
[ 56.226014] Bluetooth: HCI device and connection manager initialized
[ 56.226018] Bluetooth: HCI socket layer initialized
[ 56.266394] Bluetooth: L2CAP ver 2.8
[ 56.266400] Bluetooth: L2CAP socket layer initialized
[ 56.368612] Bluetooth: RFCOMM socket layer initialized
[ 56.368724] Bluetooth: RFCOMM TTY layer initialized
[ 56.368733] Bluetooth: RFCOMM ver 1.8
[ 67.845535] NET: Registered protocol family 10
[ 67.845742] lo: Disabled Privacy Extensions
[ 74.142660] eth31: no IPv6 routers present
[ 74.824578] set_level status: 0
[ 75.290608] set_level status: 0
[ 75.788427] set_level status: 0
[ 76.274672] set_level status: 0
[ 76.760926] set_level status: 0
[ 77.248666] set_level status: 0
[ 77.528921] set_level status: 0
[ 77.773185] set_level status: 0
[ 78.115216] set_level status: 0
[ 78.512264] set_level status: 0
[ 79.029448] set_level status: 0
[ 79.566560] set_level status: 0
[ 80.081355] set_level status: 0
[ 80.603065] set_level status: 0
[ 81.153403] set_level status: 0
[ 81.677643] set_level status: 0
[ 82.209000] set_level status: 0
[ 82.719062] set_level status: 0
[ 83.209057] set_level status: 0
*************************************


页首
 用户资料  
 
2 楼 
 文章标题 :
帖子发表于 : 2007-09-12 18:54 

注册: 2007-09-02 9:30
帖子: 8
送出感谢: 0 次
接收感谢: 0 次
4520最主要问题不是驱动,而是启动时有时能启动,有时不能启动,完全是随机的,32位64位的都一样。

害的我每次启动时都只能祈祷能启动成功,试了7.10的一些测试版,仍旧如此。

我现在对ubuntu已心灰意冷,打算用opensuse了,最近10.3就要出来了。

至于声卡是alc 268,论坛里有解决方案的,最新的alsa测试版也已支持此声卡了。


页首
 用户资料  
 
显示帖子 :  排序  
发表新帖 回复这个主题  [ 2 篇帖子 ] 

当前时区为 UTC + 8 小时


在线用户

正在浏览此版面的用户:没有注册用户 和 3 位游客


不能 在这个版面发表主题
不能 在这个版面回复主题
不能 在这个版面编辑帖子
不能 在这个版面删除帖子
不能 在这个版面提交附件

前往 :  
本站点为公益性站点,用于推广开源自由软件,由 DiaHosting VPSBudgetVM VPS 提供服务。
我们认为:软件应可免费取得,软件工具在各种语言环境下皆可使用,且不会有任何功能上的差异;
人们应有定制和修改软件的自由,且方式不受限制,只要他们自认为合适。

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
简体中文语系由 王笑宇 翻译