大家看看怎么回事 诸位大神们现身吧 我知道你们就在附近!!!!!!!!

启动讨论 grub/grub2/syslinux/grub4dos/Lilo
回复
243750496
帖子: 1006
注册时间: 2012-06-09 15:40
送出感谢: 0
接收感谢: 7 次

大家看看怎么回事 诸位大神们现身吧 我知道你们就在附近!!!!!!!!

#1

帖子 243750496 » 2013-04-29 1:25

1. 确认grub和plymouth的系统配置文件是原始状态,没有应用过其它的修改方案。
2. 安装v86d和hwinfo包,下面我们要用到:
代码:
sudo apt-get install v86d hwinfo

3. 查看自己显卡支持的分辨率:
代码:
sudo hwinfo --framebuffer

引用:
> hal.1: read hal dataprocess 2597: arguments to dbus_move_error() were incorrect, assertion "(dest) == NULL || !dbus_error_is_set ((dest))" failed in file ../../dbus/dbus-errors.c line 282.
This is normally a bug in some application using the D-Bus library.
libhal.c 3483 : Error unsubscribing to signals, error=The name org.freedesktop.Hal was not provided by any .service files
02: None 00.0: 11001 VESA Framebuffer
[Created at bios.464]
Unique ID: rdCR.gPBMypaP+07
Hardware Class: framebuffer
Model: "NVIDIA GeForce
"
Vendor: "NVIDIA Corporation"
Device: "NVIDIA GeForce
"
SubVendor: "NVIDIA"
SubDevice:
Revision: "Chip Rev"
Memory Size: 14 MB
Memory Range: 0xf1000000-0xf1dfffff (rw)
Mode 0x0300: 640x400 (+640), 8 bits
Mode 0x0301: 640x480 (+640), 8 bits
Mode 0x0303: 800x600 (+800), 8 bits
Mode 0x0305: 1024x768 (+1024), 8 bits
Mode 0x0307: 1280x1024 (+1280), 8 bits
Mode 0x030e: 320x200 (+640), 16 bits
Mode 0x030f: 320x200 (+1280), 24 bits
Mode 0x0311: 640x480 (+1280), 16 bits
Mode 0x0312: 640x480 (+2560), 24 bits
Mode 0x0314: 800x600 (+1600), 16 bits
Mode 0x0315: 800x600 (+3200), 24 bits
Mode 0x0317: 1024x768 (+2048), 16 bits
Mode 0x0318: 1024x768 (+4096), 24 bits
Mode 0x031a: 1280x1024 (+2560), 16 bits
Mode 0x031b: 1280x1024 (+5120), 24 bits
Mode 0x0330: 320x200 (+320), 8 bits
Mode 0x0331: 320x400 (+320), 8 bits
Mode 0x0332: 320x400 (+640), 16 bits
Mode 0x0333: 320x400 (+1280), 24 bits
Mode 0x0334: 320x240 (+320), 8 bits
Mode 0x0335: 320x240 (+640), 16 bits
Mode 0x0336: 320x240 (+1280), 24 bits
Mode 0x033d: 640x400 (+1280), 16 bits
Mode 0x033e: 640x400 (+2560), 24 bits
Mode 0x0345: 1600x1200 (+1600), 8 bits
Mode 0x0346: 1600x1200 (+3200), 16 bits
Mode 0x034a: 1600x1200 (+6400), 24 bits
Mode 0x034b: 1366x768 (+1368), 8 bits
Mode 0x034c: 1366x768 (+2736), 16 bits
Mode 0x034d: 1366x768 (+5472), 24 bits
Mode 0x0360: 1280x800 (+1280), 8 bits
Mode 0x0361: 1280x800 (+5120), 24 bits
Mode 0x0362: 768x480 (+768), 8 bits
Mode 0x0363: 848x480 (+3392), 24 bits
Config Status: cfg=new, avail=yes, need=no, active=unknown



4. 修改/etc/default/grub文件,使用uvesafb的framebuffer来启动
代码:
sudo gedit /etc/default/grub

把下面的两行
引用:
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"

引用:
#GRUB_GFXMODE=640×480

修改为:
引用:
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash nomodeset video=uvesafb:mode_option=1366×768-24,mtrr=3,scroll=ywrap"

引用:
GRUB_GFXMODE=1366×768
注意要把前面的#去掉。
5. 修改/etc/initramfs-tools/modules文件,
代码:
sudo gedit /etc/initramfs-tools/modules

添加下面这行:
引用:
uvesafb mode_option=1366×768-24 mtrr=3 scroll=ywrap

添加结果:
# List of modules that you want to include in your initramfs.
# They will be loaded at boot time in the order below.
#
# Syntax: module_name [args ...]
#
# You must run update-initramfs(8) to effect this change.
#
# Examples:
#
# raid1
# sd_mod
uvesafb mode_option=1366×768-24 mtrr=3 scroll=ywrap
是在末尾添加么?

6. 运行下面的命令,启用framebuffer:
代码:
echo FRAMEBUFFER=y | sudo tee /etc/initramfs-tools/conf.d/splash

7. 运行下面的命令,更新grub配置文件:
代码:
sudo update-grub2
sudo update-initramfs -u

关机
IMG_2788.JPG
启动
IMG_2789.JPG
天阿
IMG_2791.JPG
然后显示英伟达标志
然后进入桌面 我猜是启动时的ubuntu标志变成了条纹(这算花屏么)
为什么?怎么解决??黑色启动菜单是怎么回事?为什么?怎么解决

悬赏的conky
屏幕截图.png
想要的回答问题哦!
上次由 243750496 在 2013-05-01 22:18,总共编辑 10 次。
头像
b33e
论坛版主
帖子: 3866
注册时间: 2011-06-07 14:20
系统: Mint18
送出感谢: 16 次
接收感谢: 62 次

Re: 求大神!纠NVIDIA驱动安装后分辨率过低问题后 关机分辨率正常开机显示条纹!救命啊!!!!!!!!!!!!!!

#2

帖子 b33e » 2013-04-29 11:03

compiz特效那玩意,没啥用,还老崩溃
243750496
帖子: 1006
注册时间: 2012-06-09 15:40
送出感谢: 0
接收感谢: 7 次

Re: 求大神!NVIDIA驱动安装后分辨率过低!回答完这最后一个问题我就发奖(漂亮conky)!到现在都没解决!!!!

#3

帖子 243750496 » 2013-05-01 15:56

有没有大神?小弟先谢过了~
回复

回到 “启动和引导”