当前时区为 UTC + 8 小时



发表新帖 回复这个主题  [ 2 篇帖子 ] 
作者 内容
1 楼 
 文章标题 : 关于2个EE和显卡驱动模块
帖子发表于 : 2009-09-12 21:58 
头像

注册: 2009-03-10 13:04
帖子: 7803
送出感谢: 1
接收感谢: 0 次
:em04 目前vesa驱动显示性能低下


/var/log/Xorg.0.log 提取的EE
代码:
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
   compiled for 1.6.3.901, module version = 2.8.1
   Module class: X.Org Video Driver
   ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "i810"
(WW) Warning, couldn't open module i810
(II) UnloadModule: "i810"
(EE) Failed to load module "i810" (module does not exist, 0)
(II) LoadModule: "vesa"
(II) Loading /usr/lib/xorg/modules/drivers//vesa_drv.so
(II) Module vesa: vendor="X.Org Foundation"
   compiled for 1.6.0, module version = 2.2.0
   Module class: X.Org Video Driver
   ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "fbdev"
(WW) Warning, couldn't open module fbdev
(II) UnloadModule: "fbdev"
(EE) Failed to load module "fbdev" (module does not exist, 0)
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
   i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
   E7221 (i915), 915GM, 945G, 945GM, 945GME, IGD_GM, IGD_G, 965G, G35,
   965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
   Mobile Intel® GM45 Express Chipset,
   Intel Integrated Graphics Device, G45/G43, Q45/Q43, G41, IGDNG_D,
   IGDNG_M
(II) VESA: driver for VESA chipsets: vesa
(II) Primary Device is: PCI 00@00:02:0
(II) resource ranges after xf86ClaimFixedResources() call:
   [0] -1   0   0xffffffff - 0xffffffff (0x1) MX[B]
   [1] -1   0   0x000f0000 - 0x000fffff (0x10000) MX[B]
   [2] -1   0   0x000c0000 - 0x000effff (0x30000) MX[B]
   [3] -1   0   0x00000000 - 0x0009ffff (0xa0000) MX[B]
   [4] -1   0   0x0000ffff - 0x0000ffff (0x1) IX[B]
   [5] -1   0   0x00000000 - 0x00000000 (0x1) IX[B]
(WW) Falling back to old probe method for vesa


这是完整班本的/var/log/Xorg.0.log

代码:
X.Org X Server 1.6.3.901 (1.6.4 RC 1)
Release Date: 2009-8-25
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.30-ARCH i686
Current Operating System: Linux fighter 2.6.30-ARCH #1 SMP PREEMPT Wed Sep 9 12:37:32 UTC 2009 i686
Build Date: 04 September 2009  03:37:03PM
 
   Before reporting problems, check http://wiki.x.org
   to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
   (++) from command line, (!!) notice, (II) informational,
   (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Sep 13 05:53:58 2009
(II) Loader magic: 0xec0
(II) Module ABI versions:
   X.Org ANSI C Emulation: 0.4
   X.Org Video Driver: 5.0
   X.Org XInput driver : 4.0
   X.Org Server Extension : 2.0
(II) Loader running on linux
(++) using VT number 7

(--) PCI:*(0:0:2:0) 8086:27ae:103c:30d5 Intel Corporation Mobile 945GME Express Integrated Graphics Controller rev 3, Mem @ 0xf0400000/524288, 0xe0000000/268435456, 0xf0480000/262144, I/O @ 0x00003000/8
(--) PCI: (0:0:2:1) 8086:27a6:103c:30d5 Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller rev 3, Mem @ 0xf0500000/524288
(==) Using default built-in configuration (39 lines)
(==) --- Start of built-in configuration ---
   Section "Device"
      Identifier   "Builtin Default intel Device 0"
      Driver   "intel"
   EndSection
   Section "Screen"
      Identifier   "Builtin Default intel Screen 0"
      Device   "Builtin Default intel Device 0"
   EndSection
   Section "Device"
      Identifier   "Builtin Default i810 Device 0"
      Driver   "i810"
   EndSection
   Section "Screen"
      Identifier   "Builtin Default i810 Screen 0"
      Device   "Builtin Default i810 Device 0"
   EndSection
   Section "Device"
      Identifier   "Builtin Default vesa Device 0"
      Driver   "vesa"
   EndSection
   Section "Screen"
      Identifier   "Builtin Default vesa Screen 0"
      Device   "Builtin Default vesa Device 0"
   EndSection
   Section "Device"
      Identifier   "Builtin Default fbdev Device 0"
      Driver   "fbdev"
   EndSection
   Section "Screen"
      Identifier   "Builtin Default fbdev Screen 0"
      Device   "Builtin Default fbdev Device 0"
   EndSection
   Section "ServerLayout"
      Identifier   "Builtin Default Layout"
      Screen   "Builtin Default intel Screen 0"
      Screen   "Builtin Default i810 Screen 0"
      Screen   "Builtin Default vesa Screen 0"
      Screen   "Builtin Default fbdev Screen 0"
   EndSection
(==) --- End of built-in configuration ---
(==) ServerLayout "Builtin Default Layout"
(**) |-->Screen "Builtin Default intel Screen 0" (0)
(**) |   |-->Monitor "<default monitor>"
(**) |   |-->Device "Builtin Default intel Device 0"
(==) No monitor specified for screen "Builtin Default intel Screen 0".
   Using a default monitor configuration.
(**) |-->Screen "Builtin Default i810 Screen 0" (1)
(**) |   |-->Monitor "<default monitor>"
(**) |   |-->Device "Builtin Default i810 Device 0"
(==) No monitor specified for screen "Builtin Default i810 Screen 0".
   Using a default monitor configuration.
(**) |-->Screen "Builtin Default vesa Screen 0" (2)
(**) |   |-->Monitor "<default monitor>"
(**) |   |-->Device "Builtin Default vesa Device 0"
(==) No monitor specified for screen "Builtin Default vesa Screen 0".
   Using a default monitor configuration.
(**) |-->Screen "Builtin Default fbdev Screen 0" (3)
(**) |   |-->Monitor "<default monitor>"
(**) |   |-->Device "Builtin Default fbdev Device 0"
(==) No monitor specified for screen "Builtin Default fbdev Screen 0".
   Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/Type1" does not exist.
   Entry deleted from font path.
(==) FontPath set to:
   /usr/share/fonts/misc,
   /usr/share/fonts/100dpi:unscaled,
   /usr/share/fonts/75dpi:unscaled,
   /usr/share/fonts/TTF,
   built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
   If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) System resource ranges:
   [0] -1   0   0xffffffff - 0xffffffff (0x1) MX[B]
   [1] -1   0   0x000f0000 - 0x000fffff (0x10000) MX[B]
   [2] -1   0   0x000c0000 - 0x000effff (0x30000) MX[B]
   [3] -1   0   0x00000000 - 0x0009ffff (0xa0000) MX[B]
   [4] -1   0   0x0000ffff - 0x0000ffff (0x1) IX[B]
   [5] -1   0   0x00000000 - 0x00000000 (0x1) IX[B]
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
   compiled for 1.6.3.901, module version = 1.0.0
   Module class: X.Org Server Extension
   ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
   compiled for 1.6.3.901, module version = 1.0.0
   Module class: X.Org Server Extension
   ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
   compiled for 1.6.3.901, module version = 1.0.0
   ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
   compiled for 1.6.3.901, module version = 1.13.0
   Module class: X.Org Server Extension
   ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
   compiled for 1.6.3.901, module version = 1.0.0
   ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
   compiled for 1.6.3.901, module version = 1.1.0
   ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
   compiled for 1.6.3.901, module version = 2.8.1
   Module class: X.Org Video Driver
   ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "i810"
(WW) Warning, couldn't open module i810
(II) UnloadModule: "i810"
(EE) Failed to load module "i810" (module does not exist, 0)
(II) LoadModule: "vesa"
(II) Loading /usr/lib/xorg/modules/drivers//vesa_drv.so
(II) Module vesa: vendor="X.Org Foundation"
   compiled for 1.6.0, module version = 2.2.0
   Module class: X.Org Video Driver
   ABI class: X.Org Video Driver, version 5.0
(II) LoadModule: "fbdev"
(WW) Warning, couldn't open module fbdev
(II) UnloadModule: "fbdev"
(EE) Failed to load module "fbdev" (module does not exist, 0)
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
   i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
   E7221 (i915), 915GM, 945G, 945GM, 945GME, IGD_GM, IGD_G, 965G, G35,
   965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
   Mobile Intel® GM45 Express Chipset,
   Intel Integrated Graphics Device, G45/G43, Q45/Q43, G41, IGDNG_D,
   IGDNG_M
(II) VESA: driver for VESA chipsets: vesa
(II) Primary Device is: PCI 00@00:02:0
(II) resource ranges after xf86ClaimFixedResources() call:
   [0] -1   0   0xffffffff - 0xffffffff (0x1) MX[B]
   [1] -1   0   0x000f0000 - 0x000fffff (0x10000) MX[B]
   [2] -1   0   0x000c0000 - 0x000effff (0x30000) MX[B]
   [3] -1   0   0x00000000 - 0x0009ffff (0xa0000) MX[B]
   [4] -1   0   0x0000ffff - 0x0000ffff (0x1) IX[B]
   [5] -1   0   0x00000000 - 0x00000000 (0x1) IX[B]
(WW) Falling back to old probe method for vesa
(II) resource ranges after probing:
   [0] -1   0   0xffffffff - 0xffffffff (0x1) MX[B]
   [1] -1   0   0x000f0000 - 0x000fffff (0x10000) MX[B]
   [2] -1   0   0x000c0000 - 0x000effff (0x30000) MX[B]
   [3] -1   0   0x00000000 - 0x0009ffff (0xa0000) MX[B]
   [4] 0   0   0x000a0000 - 0x000affff (0x10000) MS[B]
   [5] 0   0   0x000b0000 - 0x000b7fff (0x8000) MS[B]
   [6] 0   0   0x000b8000 - 0x000bffff (0x8000) MS[B]
   [7] -1   0   0x0000ffff - 0x0000ffff (0x1) IX[B]
   [8] -1   0   0x00000000 - 0x00000000 (0x1) IX[B]
   [9] 0   0   0x000003b0 - 0x000003bb (0xc) IS[B]
   [10] 0   0   0x000003c0 - 0x000003df (0x20) IS[B]
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
   compiled for 1.6.3.901, module version = 0.1.0
   ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 7, (OK)
drmOpenByBusid: drmOpenMinor returns 7
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) intel(0): Creating default Display subsection in Screen section
   "Builtin Default intel Screen 0" for depth/fbbpp 24/32
(==) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) 945GME
(--) intel(0): Chipset: "945GME"
(--) intel(0): Linear framebuffer at 0xE0000000
(--) intel(0): IO registers at addr 0xF0400000 size 524288
(WW) intel(0): libpciaccess reported 0 rom size, guessing 64kB
(II) intel(0): No SDVO device is found in VBT
(II) intel(0): 2 display pipes available.
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) intel(0): Output VGA has no monitor section
(II) intel(0): Output LVDS has no monitor section
(II) intel(0): I2C bus "LVDSDDC_C" initialized.
(II) intel(0): Attempting to determine panel fixed mode.
(II) intel(0): I2C device "LVDSDDC_C:E-EDID segment register" registered at address 0x60.
(II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0.
(II) intel(0): EDID vendor "LPL", prod id 4609
(II) intel(0): found backlight control method /sys/class/backlight/acpi_video0
(II) intel(0): EDID vendor "LPL", prod id 4609
(II) intel(0): Output VGA disconnected
(II) intel(0): Output LVDS connected
(II) intel(0): Using exact sizes for initial modes
(II) intel(0): Output LVDS using initial mode 1280x800
(II) intel(0): detected 256 kB GTT.
(II) intel(0): detected 7932 kB stolen memory.
(==) intel(0): video overlay key set to 0x101fe
(==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
(==) intel(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
   compiled for 1.6.3.901, module version = 1.0.0
   ABI class: X.Org ANSI C Emulation, version 0.4
(II) intel(0): Comparing regs from server start up to After PreInit
(WW) intel(0): Register 0x61200 (PP_STATUS) changed from 0xc0000008 to 0xd000000a
(WW) intel(0): PP_STATUS before: on, ready, sequencing idle
(WW) intel(0): PP_STATUS after: on, ready, sequencing on
(II) UnloadModule: "vesa"
(II) Unloading /usr/lib/xorg/modules/drivers//vesa_drv.so
(==) Depth 24 pixmap format is 32 bpp
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
   [0] -1   0   0xffffffff - 0xffffffff (0x1) MX[B]
   [1] -1   0   0x000f0000 - 0x000fffff (0x10000) MX[B]
   [2] -1   0   0x000c0000 - 0x000effff (0x30000) MX[B]
   [3] -1   0   0x00000000 - 0x0009ffff (0xa0000) MX[B]
   [4] 0   0   0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
   [5] 0   0   0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
   [6] 0   0   0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
   [7] -1   0   0x0000ffff - 0x0000ffff (0x1) IX[B]
   [8] -1   0   0x00000000 - 0x00000000 (0x1) IX[B]
   [9] 0   0   0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
   [10] 0   0   0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) intel(0): Kernel reported 489216 total, 1 used
(II) intel(0): I830CheckAvailableMemory: 1956860 kB available
(II) intel(0): [DRI2] Setup complete
(**) intel(0): Framebuffer compression enabled
(**) intel(0): Tiling enabled
(**) intel(0): SwapBuffers wait enabled
(==) intel(0): VideoRam: 262144 KB
(II) intel(0): Attempting memory allocation with tiled buffers.
(II) intel(0): Tiled allocation successful.
(II) intel(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) UXA(0): Driver registered support for the following operations:
(II)         solid
(II)         copy
(II)         composite (RENDER acceleration)
(==) intel(0): Backing store disabled
(==) intel(0): Silken mouse enabled
(II) intel(0): Initializing HW Cursor
(II) intel(0): adjusting plane->pipe mappings to allow for framebuffer compression
(II) intel(0): Fixed memory allocation layout:
(II) intel(0): 0x00000000-0x005fffff: compressed frame buffer (6144 kB, 0x000000007f800000 physical
)
(II) intel(0): 0x00600000-0x00600fff: compressed ll buffer (4 kB, 0x000000007fe00000 physical
)
(II) intel(0): 0x00601000-0x0060afff: HW cursors (40 kB, 0x000000007fe01000 physical
)
(II) intel(0): 0x0060b000-0x0060bfff: overlay registers (4 kB, 0x000000007fe0b000 physical
)
(II) intel(0): 0x007bf000:            end of stolen memory
(II) intel(0): 0x007bf000-0x0f9f3fff: DRI memory manager (248020 kB)
(II) intel(0): 0x10000000:            end of aperture
(II) intel(0): BO memory allocation layout:
(II) intel(0): 0x007bf000:            start of memory manager
(II) intel(0): 0x00800000-0x00ffffff: front buffer (8192 kB) X tiled
(II) intel(0): 0x0f9f4000:            end of memory manager
(II) intel(0): using SSC reference clock of 96 MHz
(II) intel(0): Selecting standard 18 bit TMDS pixel format.
(II) intel(0): Output configuration:
(II) intel(0):   Pipe A is off
(II) intel(0):   Display plane B is now disabled and connected to pipe A.
(II) intel(0):   Pipe B is on
(II) intel(0):   Display plane A is now enabled and connected to pipe B.
(II) intel(0):   Output VGA is connected to pipe none
(II) intel(0):   Output LVDS is connected to pipe B
(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) intel(0): DPMS enabled
(==) intel(0): Intel XvMC decoder disabled
(II) intel(0): Set up textured video
(II) intel(0): Set up overlay video
(II) intel(0): direct rendering: DRI2 Enabled
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: enabled GLX_MESA_copy_sub_buffer
(II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
(II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
(II) AIGLX: Loaded and initialized /usr/lib/xorg/modules/dri/i915_dri.so
(II) GLX: Initialized DRI2 GL provider for screen 0
(II) intel(0): Setting screen physical size to 304 x 190
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
   compiled for 1.6.3, module version = 2.2.5
   Module class: X.Org XInput Driver
   ABI class: X.Org XInput driver, version 4.0
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Macintosh mouse button emulation
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) filter chain progression: 2.00
(**) Macintosh mouse button emulation: (accel) filter stage 0: 20.00 ms
(**) Macintosh mouse button emulation: (accel) set acceleration profile 0
(II) Macintosh mouse button emulation: initialized for relative axes.
(II) config/hal: Adding input device A4TECH USB Device
(**) A4TECH USB Device: always reports core events
(**) A4TECH USB Device: Device: "/dev/input/event8"
(II) A4TECH USB Device: Found 20 mouse buttons
(II) A4TECH USB Device: Found x and y relative axes
(II) A4TECH USB Device: Found scroll wheel(s)
(II) A4TECH USB Device: Configuring as mouse
(**) A4TECH USB Device: YAxisMapping: buttons 4 and 5
(**) A4TECH USB Device: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "A4TECH USB Device" (type: MOUSE)
(**) A4TECH USB Device: (accel) keeping acceleration scheme 1
(**) A4TECH USB Device: (accel) filter chain progression: 2.00
(**) A4TECH USB Device: (accel) filter stage 0: 20.00 ms
(**) A4TECH USB Device: (accel) set acceleration profile 0
(II) A4TECH USB Device: initialized for relative axes.
(II) config/hal: Adding input device A4TECH USB Device
(**) A4TECH USB Device: always reports core events
(**) A4TECH USB Device: Device: "/dev/input/event9"
(II) A4TECH USB Device: Found 1 mouse buttons
(II) A4TECH USB Device: Found scroll wheel(s)
(II) A4TECH USB Device: Found x and y absolute axes
(II) A4TECH USB Device: Found keys
(II) A4TECH USB Device: Configuring as mouse
(II) A4TECH USB Device: Configuring as keyboard
(**) A4TECH USB Device: YAxisMapping: buttons 4 and 5
(**) A4TECH USB Device: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "A4TECH USB Device" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(**) A4TECH USB Device: (accel) keeping acceleration scheme 1
(**) A4TECH USB Device: (accel) filter chain progression: 2.00
(**) A4TECH USB Device: (accel) filter stage 0: 20.00 ms
(**) A4TECH USB Device: (accel) set acceleration profile 0
(II) A4TECH USB Device: initialized for absolute axes.
(II) config/hal: Adding input device Sleep Button
(**) Sleep Button: always reports core events
(**) Sleep Button: Device: "/dev/input/event4"
(II) Sleep Button: Found keys
(II) Sleep Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Video Bus
(**) Video Bus: always reports core events
(**) Video Bus: Device: "/dev/input/event7"
(II) Video Bus: Found keys
(II) Video Bus: Configuring as keyboard
(II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) config/hal: Adding input device Power Button
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event2"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "evdev"
(**) Option "xkb_layout" "us"
(II) intel(0): EDID vendor "LPL", prod id 4609
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0   69.30  1280 1328 1360 1405  800 803 809 822 -hsync -vsync (49.3 kHz)
(II) intel(0): EDID vendor "LPL", prod id 4609
(II) intel(0): EDID vendor "LPL", prod id 4609
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0   69.30  1280 1328 1360 1405  800 803 809 822 -hsync -vsync (49.3 kHz)
(II) intel(0): EDID vendor "LPL", prod id 4609
(II) intel(0): EDID vendor "LPL", prod id 4609
(II) intel(0): Printing DDC gathered Modelines:
(II) intel(0): Modeline "1280x800"x0.0   69.30  1280 1328 1360 1405  800 803 809 822 -hsync -vsync (49.3 kHz)
(II) intel(0): EDID vendor "LPL", prod id 4609


_________________
广告位招租


最后由 nuanhuai 编辑于 2009-09-12 23:13,总共编辑了 1 次

页首
 用户资料  
 
2 楼 
 文章标题 : Re: 关于2个EE和显卡驱动模块
帖子发表于 : 2009-09-12 22:04 
头像

注册: 2008-12-13 19:39
帖子: 13284
地址: 物华天宝人杰地灵
送出感谢: 1
接收感谢: 6
长长的罗格,比鲸鞭还长。。。 :em20

响应一叶号召,回贴不忘拉票。 :em02
viewtopic.php?f=1&t=226128#各位兄弟姐妹,赶快去给Ubuntu中文投票。投票日期截止到9月20,每天都可以投 :em11


_________________
行到水穷处,坐看云起时。
海内生明月,天涯共此夕。
--------------------吾本独!


页首
 用户资料  
 
显示帖子 :  排序  
发表新帖 回复这个主题  [ 2 篇帖子 ] 

当前时区为 UTC + 8 小时


在线用户

正在浏览此版面的用户:没有注册用户 和 1 位游客


不能 在这个版面发表主题
不能 在这个版面回复主题
不能 在这个版面编辑帖子
不能 在这个版面删除帖子
不能 在这个版面提交附件

前往 :  
本站点为公益性站点,用于推广开源自由软件,由 DiaHosting VPSBudgetVM VPS 提供服务。
我们认为:软件应可免费取得,软件工具在各种语言环境下皆可使用,且不会有任何功能上的差异;
人们应有定制和修改软件的自由,且方式不受限制,只要他们自认为合适。

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
简体中文语系由 王笑宇 翻译