[问题] 安装cadence ic5033中遇到的 问题?

OOo,TeX,KO,ABI,GIMP,Picasa,ProE,QCAD,Inkscape,Kicad,Eagle
回复
coconuttree01
帖子: 2
注册时间: 2007-04-30 19:12
送出感谢: 0
接收感谢: 0

[问题] 安装cadence ic5033中遇到的 问题?

#1

帖子 coconuttree01 » 2007-04-30 19:51

运行SETUP.SH后

Located CDROM at /mnt/cdrom-1

Specify path of install directory [OR type [RETURN] to exit]: /home/ic5033

Setting up softload for lnx86 in /home/ic5033

The following tar errors were detected:
/bin/tar: 从成员名中删除开头的“/”

Could not set up SoftLoad in /home/ic5033

You must have write permissions to install directory and all its subdirectories
and atleast 10 MB available disk space in install directory.

Specify path of install directory [OR type [RETURN] to exit]:

请大家帮忙看看我用root安装的,硬盘空间足够大)。
keenboyee
帖子: 22
注册时间: 2007-01-17 22:29
送出感谢: 0
接收感谢: 0

#2

帖子 keenboyee » 2007-05-09 16:39

我在7。04下安装cadence spb155时也出现了相同的错误,不知道该怎么解决
radar
帖子: 1
注册时间: 2007-05-10 2:55
送出感谢: 0
接收感谢: 0

#3

帖子 radar » 2007-05-10 2:57

something wrong with your tar, you should check this forum

www.edaboard.com

I'm going to install it too, hopefully I can get it done:)
sakulaqi
帖子: 16
注册时间: 2005-05-23 11:54
送出感谢: 0
接收感谢: 0

#4

帖子 sakulaqi » 2007-06-11 1:36

if ubuntu's version >=606
it is impossible to run ic5<5141usr4 (5141 is ok) or spb.
i don't konw about spb/157 because i cannot got it from anywhere.
marcusliang
帖子: 1
注册时间: 2007-06-28 5:51
送出感谢: 0
接收感谢: 0

Can u show how to install Cadence IC5141 on Ubuntu 7.04?

#5

帖子 marcusliang » 2007-06-28 5:53

I try to install Cadence IC5141 on ubuntu 7.04; however it is not work after I type icfb&.
the system shows errors.
I am afraid my installation is not correct.
timchu
帖子: 1
注册时间: 2007-08-06 21:00
送出感谢: 0
接收感谢: 0

Re: [问题] 安装cadence ic5033中遇到的 问题?

#6

帖子 timchu » 2007-08-11 15:03

出现这个错误后,进入 /home/ic5033
然后里边有个install/linux.lnx(忘记了)
里边有个softload吧。运行那个就可以安装了







quote="coconuttree01"]运行SETUP.SH后

Located CDROM at /mnt/cdrom-1

Specify path of install directory [OR type [RETURN] to exit]: /home/ic5033

Setting up softload for lnx86 in /home/ic5033

The following tar errors were detected:
/bin/tar: 从成员名中删除开头的“/”

Could not set up SoftLoad in /home/ic5033

You must have write permissions to install directory and all its subdirectories
and atleast 10 MB available disk space in install directory.

Specify path of install directory [OR type [RETURN] to exit]:

请大家帮忙看看我用root安装的,硬盘空间足够大)。[/quote]
coolgezi
帖子: 1
注册时间: 2010-03-11 22:28
送出感谢: 0
接收感谢: 0

Re: [问题] 安装cadence ic5033中遇到的 问题?

#7

帖子 coolgezi » 2010-05-17 18:24

我是在REDHAT 4.7下面安装IC5141的,并能成功运行,画版图。如果要在ubuntu下面安装的话,会提示tar的版本有问题,或者缺少些什么库之类的。
回复

回到 “办公、图像、机械电子设计等”