[问题]ubuntu登陆界面死循环

为当前最终发行版之前的所有版本提供支持
回复
topgunubuntu
帖子: 3
注册时间: 2008-05-06 16:38
送出感谢: 0
接收感谢: 0

[问题]ubuntu登陆界面死循环

#1

帖子 topgunubuntu » 2008-05-11 8:47

ubuntu版本似乎是6.0.?的,安装了一个realplayer,打开的时候突然死机,无奈只好强行断电关机(笔记本,其他方法关机不奏效),
再次开机,系统顺利加载,最后启动x出现登陆界面,输入用户名-〉回车->输入密码-〉回车,屏幕中央出现一个
显示各个x部件加载状况的小窗口,第一个也是唯一一个显示的是window manager图标,然后系统退回到了登陆窗口,
再次输入用户名-〉回车-输入密码-〉回车-〉显示小窗口-〉小窗口显示window manager图标-〉跳回登陆窗口,如此反复
我都输入了10几次了,仍然是这样登陆死循环,小弟菜鸟,请高手帮忙指点,谢谢!!
qdzheng
帖子: 277
注册时间: 2006-12-03 23:00
送出感谢: 0
接收感谢: 0

#2

帖子 qdzheng » 2008-05-11 13:18

ctrl+alt+F1先登录到终端环境下,然后手工启动X服务,看看有什么错误信息没。
终端上可能会有一些错误信息,输入dmesg也可以看到相关信息,
有的话,将错误贴出来,让大家帮着看一下,或许有办法帮你。
好吧,听某人的建议,修改下签名。
wangchengaiqi
帖子: 2
注册时间: 2008-11-20 14:32
送出感谢: 0
接收感谢: 0

Re: [问题]ubuntu登陆界面死循环

#3

帖子 wangchengaiqi » 2011-03-07 11:18

[ 3.094619] device-mapper: multipath: version 1.1.1 loaded
[ 3.094666] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 3.094793] EISA: Probing bus 0 at eisa.0
[ 3.094834] EISA: Cannot allocate resource for mainboard
[ 3.094878] Cannot allocate resource for EISA slot 1
[ 3.094921] Cannot allocate resource for EISA slot 2
[ 3.094963] Cannot allocate resource for EISA slot 3
[ 3.095006] Cannot allocate resource for EISA slot 4
[ 3.095048] Cannot allocate resource for EISA slot 5
[ 3.095091] Cannot allocate resource for EISA slot 6
[ 3.095133] Cannot allocate resource for EISA slot 7
[ 3.095176] Cannot allocate resource for EISA slot 8
[ 3.095218] EISA: Detected 0 cards.
[ 3.095303] cpuidle: using governor ladder
[ 3.095344] cpuidle: using governor menu
[ 3.095607] TCP cubic registered
[ 3.095740] NET: Registered protocol family 10
[ 3.096075] lo: Disabled Privacy Extensions
[ 3.096287] NET: Registered protocol family 17
....

[ 16.365265] type=1400 audit(1299466846.764:9): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1338 comm="apparmor_parser"
[ 16.375950] type=1400 audit(1299466846.772:10): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=1355 comm="apparmor_parser"
[ 16.376526] type=1400 audit(1299466846.776:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1355 comm="apparmor_parser"
[ 16.460161] e1000e 0000:00:19.0: irq 48 for MSI/MSI-X
[ 16.512315] e1000e 0000:00:19.0: irq 48 for MSI/MSI-X
[ 16.512605] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.228859] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 18.228862] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 18.229015] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 29.000261] eth0: no IPv6 routers present
[ 29.060328] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,commit=0
[ 45.235881] lo: Disabled Privacy Extensions
附件
abc.log.txt
详细的log
(49.34 KiB) 下载 38 次
回复

回到 “老旧版本支持”