当前时区为 UTC + 8 小时



发表新帖 回复这个主题  [ 2 篇帖子 ] 
作者 内容
1 楼 
 文章标题 : [问题]Sensors Applet 中显示 temp1 temp3 是什么意思?
帖子发表于 : 2008-08-02 0:55 
头像

注册: 2007-12-16 0:45
帖子: 25
送出感谢: 0 次
接收感谢: 0 次
DELL Inspiron 安装 Ubuntu 8.04 (AMD64)

安装 Sensors Applet 后,能看到三个 sensors :
-----------------------------------
sensor label
acpi ->
THRM CPU

libsensors ->
temp1 temp1
temp3 temp3
-----------------------------------
请问如何确定 temp1 和 temp3 是什么东东?

我同时也安装了 Computer Temperature Monitor ,此软件也类似地给出 hwmon0(1) 和 hwmon0(3) 两个温度传感器。

我也试过执行 sudo sensors-detect ,不过最后好像只找到一个CPU的传感器。详细如下:

============
owen@owen-laptop:~$ sudo sensors-detect
# sensors-detect revision 5016 (2007-11-11 22:20:16 +0100)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): y
Probing for PCI bus adapters...
Use driver `i2c-piix4' for device 0000:00:14.0: ATI Technologies Inc SB600 SMBus

We will now try to load each adapter module in turn.
Module `i2c-piix4' already loaded.
If you have undetectable or unsupported adapters, you can have them
scanned by manually loading the modules before running this script.

To continue, we need module `i2c-dev' to be loaded.
Do you want to load `i2c-dev' now? (YES/no): y
Module loaded successfully.

We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.

Next adapter: SMBus PIIX4 adapter at 8410 (i2c-0)
Do you want to scan it? (YES/no/selectively): y
Client found at address 0x50
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'... No
Client found at address 0x52
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... Yes
(confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'... No

Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): y
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM78-J' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Probing for `Silicon Integrated Systems SIS5595'... No
Probing for `VIA VT82C686 Integrated Sensors'... No
Probing for `VIA VT8231 Integrated Sensors'... No
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No

Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... Yes
Found `Nat. Semi. PC87591 Super IO'
(but not activated)
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Fintek'... No
Trying family `ITE'... No

Some CPUs or memory controllers may also contain embedded sensors.
Do you want to scan for them? (YES/no): y
AMD K8 thermal sensors... Success!
(driver `k8temp')
AMD K10 thermal sensors... No
Intel Core family thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No

Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `k8temp' (should be inserted):
Detects correctly:
* Chip `AMD K8 thermal sensors' (confidence: 9)

I will now generate the commands needed to load the required modules.
Just press ENTER to continue:

To load everything that is needed, add this to /etc/modules:

#----cut here----
# Chip drivers
k8temp
#----cut here----

Do you want to add these lines automatically? (yes/NO)n

============


页首
 用户资料  
 
2 楼 
 文章标题 :
帖子发表于 : 2008-08-02 12:02 
头像

注册: 2007-10-06 18:40
帖子: 4313
送出感谢: 0 次
接收感谢: 5
南桥,北桥?


_________________
E=m c^2


页首
 用户资料  
 
显示帖子 :  排序  
发表新帖 回复这个主题  [ 2 篇帖子 ] 

当前时区为 UTC + 8 小时


在线用户

正在浏览此版面的用户:Google [Bot] 和 4 位游客


不能 在这个版面发表主题
不能 在这个版面回复主题
不能 在这个版面编辑帖子
不能 在这个版面删除帖子
不能 在这个版面提交附件

前往 :  
本站点为公益性站点,用于推广开源自由软件,由 DiaHosting VPSBudgetVM VPS 提供服务。
我们认为:软件应可免费取得,软件工具在各种语言环境下皆可使用,且不会有任何功能上的差异;
人们应有定制和修改软件的自由,且方式不受限制,只要他们自认为合适。

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
简体中文语系由 王笑宇 翻译