[问题]NV/ATI 安装6.10进度条走满后就黑屏,Partially Solved!

为当前最终发行版之前的所有版本提供支持
回复
pootoo
帖子: 4
注册时间: 2007-02-07 21:37
送出感谢: 0
接收感谢: 0

[问题]NV/ATI 安装6.10进度条走满后就黑屏,Partially Solved!

#1

帖子 pootoo » 2007-02-07 21:54

从Live CD boot.
选择安装后首先进度条象Nescape那样来回扫几次(验证软件包?),然后就一点点增加,可是等到走满后,屏幕就黑掉了.光盘闪了几秒钟后,也不闪了.按键盘caplock不会引起灯亮或灭.按Ctrl+Alt+F2没有反应.
尝试过用VGA=771安装,除了前面的Splash会不在正中,其他现象一样.

机器配置:
nForce2 Ultra + AMD Sempron2400 (集成网卡和声卡,运行5.10时是没有问题的)
DDR400 512Mx2
Seagate 酷鱼10 250G硬盘
ATI Radeon 9600TX 128MB (这个也有点乱实际上是9550,刷成的9600TX,不过运行5.10没有问题的)
DELL 1905 LCD(这个有点乱,刷新率只能够到70,不能够到75!)
还没有下载Alternative CD.

乱猜是Xserver坏掉了.
请问怎样获得log信息?
怎样从Live CD用非图形界面安装?已知boot: live text没有用处.

[更新]
刚才在ubuntu英文站学到了一点方法:F6->去掉quiet splash后boot,会显示出一些log信息。
经过这种方法,获得了一些log,目前看到的是Gnome Manager启动后,字体会产生变化,但是仍然有显示,
接着启动HP Linux Printer ...也是Ok,接着LCD就没有信号了。

Since I am now in Ubuntu 6.10 without scim installed yet. I have to type in English for a while.
Next, I tried to add "single" into the boot option, and make the system boot into single mode, where I had chance to use console before X11 is started.

pico /etc/X11/xorg.conf

Find the section that describle my video adapter "ati" and change it into "vesa", which will disable video acceleration.
Ctrl^O to write the config file back.
Ctrl^X to quit the pico.

type startx
and after around 20 second, I am now finally enter into the Xwindow.

I think maybe it is the reason for many NV/ATI video adpater holder that could not boot correctly with Live CD. So it's for your information that you could still enter 6.10 by Live CD.

I will continue to improve this post in future.
Find
上次由 pootoo 在 2007-02-07 22:53,总共编辑 3 次。
头像
zmcbb30
帖子: 2717
注册时间: 2006-09-30 0:32
来自: 巴拉特星系第四行星──海尼森
送出感谢: 0
接收感谢: 0
联系:

#2

帖子 zmcbb30 » 2007-02-07 21:59

用Alternative CD试一下 ,livecd好像只能进去后安装
估计是显卡驱动的问题
头可断,血可流,靓女不可不追求
相艾唔好口,够姜就只抽

BARTON 2500+/1536MDDR400
EP8RDA3G/MX4000 128M64bit 8X
DiamondPlus9-6Y080L0-ATA133
Samsung743DF
HiweedDesktop-1.0
pootoo
帖子: 4
注册时间: 2007-02-07 21:37
送出感谢: 0
接收感谢: 0

咳,我没有下Alternative CD啊!

#3

帖子 pootoo » 2007-02-07 22:01

难道,6.10对硬件比5.10要挑剔许多吗?
没有别的解法吗?
例如能够显示一下log?把log输出到什么地方去?
Live CD不会这么没有人性化调试方法吧?
头像
zmcbb30
帖子: 2717
注册时间: 2006-09-30 0:32
来自: 巴拉特星系第四行星──海尼森
送出感谢: 0
接收感谢: 0
联系:

#4

帖子 zmcbb30 » 2007-02-07 22:04

难道,6.10对硬件比5.10要挑剔许多吗?
不能这么说,我用510就装不上
用hiweed就暴爽
用610livecd也装不上,要Alternative CD
头可断,血可流,靓女不可不追求
相艾唔好口,够姜就只抽

BARTON 2500+/1536MDDR400
EP8RDA3G/MX4000 128M64bit 8X
DiamondPlus9-6Y080L0-ATA133
Samsung743DF
HiweedDesktop-1.0
回复

回到 “老旧版本支持”