当前时区为 UTC + 8 小时



发表新帖 回复这个主题  [ 12 篇帖子 ] 
作者 内容
1 楼 
 文章标题 : 联想Y550A-PSE Nvidia 130M GT显卡 开启3D桌面特效问题~紧急求助!!!
帖子发表于 : 2009-08-29 11:59 

注册: 2009-08-25 16:29
帖子: 7
送出感谢: 0 次
接收感谢: 0 次

我的机器是刚买的Y550A,显卡是N卡,130M GT,想开启3D特效感受下。安网上说的,安了nvidia的最新显卡驱动(就是硬件驱动里检测到并推荐安装的那个)。可是一安上这个驱动,再启动的时候屏幕就会分成6份!在这6份屏幕里是可以开启3D特效的。但是重启进入recovery模式进行自动显示的修复后,再更改视觉效果为正常或扩展的时候就会提示“无法启用桌面效果!”。
打开系统-》系统管理-》nvidia x server settings时,会提示:“You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run `nvidia-xconfig` as root), and restart the X server. ”可是你在终端里运行“sudo nvidia-xconfig”命令后,会出现
VALIDATION ERROR: Data incomplete in file /etc/X11/xorg.conf.
Device section "Configured Video Device" must have a Driver
line.

Backed up file '/etc/X11/xorg.conf' as '/etc/X11/xorg.conf.backup'
New X configuration file written to '/etc/X11/xorg.conf'
提示。。。
我快崩溃了,不知哪位大虾可以帮帮我。。。
小弟先谢谢你们~~


页首
 用户资料  
 
2 楼 
 文章标题 : Re: 联想Y550A-PSE Nvidia 130M GT显卡 开启3D桌面特效问题~紧急求助!!!
帖子发表于 : 2009-08-29 12:25 
头像

注册: 2009-03-19 9:19
帖子: 1423
地址: 江苏
送出感谢: 0 次
接收感谢: 2
删除现在的,安装旧点的试试


_________________


页首
 用户资料  
 
3 楼 
 文章标题 : Re: 联想Y550A-PSE Nvidia 130M GT显卡 开启3D桌面特效问题~紧急求助!!!
帖子发表于 : 2009-08-29 12:53 

注册: 2009-08-25 16:29
帖子: 7
送出感谢: 0 次
接收感谢: 0 次
什么??显卡驱动么??我试过了,从硬件驱动那里装过,也从envyng安装过,但是都是上面的那种情况。。。


页首
 用户资料  
 
4 楼 
 文章标题 : Re: 联想Y550A-PSE Nvidia 130M GT显卡 开启3D桌面特效问题~紧急求助!!!
帖子发表于 : 2009-08-29 13:09 
头像

注册: 2009-03-19 9:19
帖子: 1423
地址: 江苏
送出感谢: 0 次
接收感谢: 2
你的内核额会不会太新了呢,是系统默认升级的不。
引用:
I recently updated FC6 and upon reboot I can't get nvidia drivers to start. I think the update contained xorg stuff but I dont know how to check... :confused:

If i go to nvidia display setting I get the following message

You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run `nvidia-xconfig` as root), and restart the X server.


and so did I...

# nvidia-xconfig

#Using X configuration file: "/etc/X11/xorg.conf".
#Backed up file '/etc/X11/xorg.conf' as '/etc/X11/xorg.conf.backup'
#New X configuration file written to '/etc/X11/xorg.conf'

restarting the x-server brings me back to the same problem where I have to get a "fresh config" in order to have x loading...

upon reboot i get an error reproducible if I try to restart nvidia service...

[root@localhost ~]# service nvidia restart
Disabling the nvidia driver: Driver already disabled. [ OK ]
Checking for module nvidia.ko: [FAILED]
nvidia.ko for kernel 2.6.20-1.2952.fc6 was not found. [WARNING]
The nvidia driver will not be enabled until one is found. [WARNING]
[root@localhost ~]#



Here is xorg.conf


# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder3) Wed Jun 13 18:39:30 PDT $

# Xorg configuration created by system-config-display

Section "ServerLayout"
Identifier "single head configuration"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
EndSection

Section "Module"
Load "glx"
EndSection

Section "InputDevice"

# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection

Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection

Section "Monitor"
Identifier "Monitor0"
VendorName "Unknown"
ModelName "Unknown"
HorizSync 30.0 - 110.0
VertRefresh 50.0 - 150.0
Option "DPMS"
EndSection

Section "Device"
Identifier "Videocard0"
Driver "nvidia"
EndSection

Section "Screen"
Identifier "Screen0"
Device "Videocard0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1152x768" "1024x$
EndSubSection
EndSection



I have looked around but strangely enough found only post in spanish regarding this error... Anyone has an idea about that?
zoodayz
2007-06-29, 10:11 AM CDT
Ah log out then if you log back into the desktop log back in as root not normal user cant su to run the cofig app the files will get over written on reboot. Also if you have Se linux on you may or may not have to have SE linux relable on reboot. Hope that helps yah
zoodayz
2007-06-29, 10:13 AM CDT
Oh also youll probly have to re insatll kmod-nvidia cause that dont get updated if your kernel got updated :(
sim39
2007-06-29, 11:23 AM CDT
I tried to relog as root and try to run nvidia-xconfig but I ended up with the same outcome as previously...

on reboot I get those errors

Failed to load module "wfb" (module does not exist, 0)
Failed to initialize GLX modul
FATAL module Nvidia not found

FATAL server error: no screen found...

:confused:
zoodayz
2007-06-29, 11:43 AM CDT
startX does what?

I tried to relog as root and try to run nvidia-xconfig but I ended up with the same outcome as previously...

on reboot I get those errors

Failed to load module "wfb" (module does not exist, 0)
Failed to initialize GLX modul
FATAL module Nvidia not found

FATAL server error: no screen found...

:confused:
zoodayz
2007-06-29, 11:56 AM CDT
Ok anhow what I would do If I can get a prompt is I would startx let it shoot out a bunch of stuff that it cant start x bla bla bla then I would let it use the failsafe mode. Let it default back to the basic drivers "if your lucky" and then if at the point I could log in I would login as root then make sure I have the proper outside repos for my Nvidia drivers then I would at prompt yumremove kmod-nvidia or however you installed the drivers "nvidia.ko" then yuminstall kmod-nvidia. then change the settings after the install in the config to suit my needs and save reboot.
Seve
2007-06-29, 01:41 PM CDT
I tried to relog as root and try to run nvidia-xconfig but I ended up with the same outcome as previously...

on reboot I get those errors

Failed to load module "wfb" (module does not exist, 0)
Failed to initialize GLX modul
FATAL module Nvidia not found

FATAL server error: no screen found...

:confused:
Hello:
What you need to do is
gedit /etc/X11/xorg.conf
and add back :
For 64bit:
Section "Files"
ModulePath "/usr/lib64/xorg/modules/extensions/nvidia"
ModulePath "/usr/lib64/xorg/modules"
EndSection
For 32bit
Section "Files"
ModulePath "/usr/lib/xorg/modules/extensions/nvidia"
ModulePath "/usr/lib/xorg/modules"
EndSection
You should also add to the end of the file :
Section "Extensions"
Option "Composite" "Enable"
EndSection

Save your work, exit and
Ctrl Alt Backspace
to restart your X server and you should be good to go.

Seve
sim39
2007-07-02, 06:27 AM CDT
thanks to everyone that helped me...

I finally found out that I was not booting the updated kernel, so two kernels were in grub and the video driver was used by the newest one.

booting with the right kernel helps a lot...


引用:
sim39
2007-06-29, 09:55 AM CDT 2007年6月29日,上午9时55分华泽
I recently updated FC6 and upon reboot I can't get nvidia drivers to start.我最近更新的FC6,并呼吁重新启动,我不能让NVIDIA驱动程序启动。 I think the update contained xorg stuff but I dont know how to check...我认为更新中包含的Xorg的东西,但我不知道如何检查... :confused: :困惑:

If i go to nvidia display setting I get the following message如果我去的NVIDIA显示设置我碰到下面的信息

You do not appear to be using the NVIDIA X driver.你似乎没有使用NVIDIA的X驱动。 Please edit your X configuration file (just run `nvidia-xconfig` as root), and restart the X server.请编辑您的X配置文件(只需运行`NVIDIA产品Xconfig文件作为根`),并重新启动X服务器。


and so did I...所以没有一..

# nvidia-xconfig #NVIDIA产品Xconfig文件

#Using X configuration file: "/etc/X11/xorg.conf". #使用X配置文件:“/ etc/X11/xorg.conf中”。
#Backed up file '/etc/X11/xorg.conf' as '/etc/X11/xorg.conf.backup' #做后盾文件'/ etc/X11/xorg.conf中'为'/ etc/X11/xorg.conf.backup'
#New X configuration file written to '/etc/X11/xorg.conf' #新的X配置文件写入'/ etc/X11/xorg.conf中'

restarting the x-server brings me back to the same problem where I have to get a "fresh config" in order to have x loading...重新启动X服务器使我回到相同的问题,在那里我要得到一个“新的配置”,以有x载入中...

upon reboot i get an error reproducible if I try to restart nvidia service...重新启动后,我得到一个错误重复的,如果我尝试重新启动NVIDIA的服务...

[root@localhost ~]# service nvidia restart [@本地主机根〜]#服务的NVIDIA重新启动
Disabling the nvidia driver: Driver already disabled.禁用NVIDIA驱动程序:驱动程序已被禁用。 [ OK ] [行]
Checking for module nvidia.ko: [FAILED]检查模块nvidia.ko:[失败]
nvidia.ko for kernel 2.6.20-1.2952.fc6 was not found. nvidia.ko用于内核2.6.20 - 1.2952.fc6没有被发现。 [WARNING] [警告]
The nvidia driver will not be enabled until one is found. NVIDIA的驱动程序将无法启用,直到找到一个。 [WARNING] [警告]
[root@localhost ~]# [@本地主机根〜]#



Here is xorg.conf这里是xorg.conf中


# nvidia-xconfig: X configuration file generated by nvidia-xconfig #NVIDIA公司Xconfig文件:X配置文件由NVIDIA生成,Xconfig文件
# nvidia-xconfig: version 1.0 (buildmeister@builder3) Wed Jun 13 18:39:30 PDT $ #NVIDIA公司Xconfig文件:版本1.0(buildmeister @ builder3)星期三6月13日18时39分30秒秒$

# Xorg configuration created by system-config-display #Xorg的配置由系统创建的配置显示器

Section "ServerLayout"科“ServerLayout”
Identifier "single head configuration"标识符“单头配置”
Screen 0 "Screen0" 0 0屏幕0“Screen0”0 0
InputDevice "Mouse0" "CorePointer"输入设备“Mouse0”“CorePointer”
InputDevice "Keyboard0" "CoreKeyboard"输入设备“Keyboard0”“CoreKeyboard”
EndSection EndSection

Section "Files"部分“档案”
EndSection EndSection

Section "Module"部分“模块”
Load "glx"加载“glx的”
EndSection EndSection

Section "InputDevice"部分“输入设备”

# generated from default #产生违约
Identifier "Mouse0"标识符“Mouse0”
Driver "mouse"司机“鼠标”
Option "Protocol" "auto"选项“议定书”,“汽车”
Option "Device" "/dev/input/mice"选择“设备”,“/开发/输入/小鼠”
Option "Emulate3Buttons" "no"选项“Emulate3Buttons项”“不”
Option "ZAxisMapping" "4 5"选项“ZAxisMapping”“4 5”
EndSection EndSection

Section "InputDevice"部分“输入设备”
Identifier "Keyboard0"标识符“Keyboard0”
Driver "kbd"司机“大骨节病”
Option "XkbModel" "pc105"选项“XkbModel”“pc105”
Option "XkbLayout" "us"选项“XkbLayout”“我们”
EndSection EndSection

Section "Monitor"科“监视器”
Identifier "Monitor0"标识符“Monitor0”
VendorName "Unknown" VendorName“未知”
ModelName "Unknown" ModelName“未知”
HorizSync 30.0 - 110.0 HorizSync 30.0 - 110.0
VertRefresh 50.0 - 150.0 VertRefresh 50.0 - 150.0
Option "DPMS"选项“的DPMS”
EndSection EndSection

Section "Device"科“设备”
Identifier "Videocard0"标识符“Videocard0”
Driver "nvidia"司机“NVIDIA公司”
EndSection EndSection

Section "Screen"科“屏幕”
Identifier "Screen0"标识符“Screen0”
Device "Videocard0"设备“Videocard0”
Monitor "Monitor0"监视器“Monitor0”
DefaultDepth 24 DefaultDepth 24
SubSection "Display"该款“显示”
Viewport 0 0口0 0
Depth 24深度24
Modes "1280x1024" "1280x960" "1280x800" "1152x864" "1152x768" "1024x$模式“1280 × 1024”,“1280 × 960”“1280x800”“1152x864”“1152x768”“1024x $
EndSubSection EndSubSection
EndSection EndSection



I have looked around but strangely enough found only post in spanish regarding this error...我环顾四周,但奇怪的是只发现后,在西班牙对这个错误... Anyone has an idea about that?任何人有一个对这一想法?
zoodayz zoodayz
2007-06-29, 10:11 AM CDT 2007年6月29日,日上午10:11华泽
Ah log out then if you log back into the desktop log back in as root not normal user cant su to run the cofig app the files will get over written on reboot.哎呀如果注销,然后登录到桌面回重新登录以root用户cannot不正常运行苏cofig应用程序的文件将得到比在重新启动时写的。 Also if you have Se linux on you may or may not have to have SE linux relable on reboot.另外如果你有你SE Linux的可能会或可能不会有东南Linux的启动relable。 Hope that helps yah希望帮助严
zoodayz zoodayz
2007-06-29, 10:13 AM CDT 2007年6月29日,日上午10:13华泽
Oh also youll probly have to re insatll kmod-nvidia cause that dont get updated if your kernel got updated :(哦也刹那间probly需要重新insatll kmod - NVIDIA的事业,dont获取更新,如果你的内核更新了:(
sim39 sim39
2007-06-29, 11:23 AM CDT 2007年6月29日,日上午11:23华泽
I tried to relog as root and try to run nvidia-xconfig but I ended up with the same outcome as previously...我试图relog为根,尝试运行NVIDIA产品Xconfig文件,但我最终与先前相同的结果了...

on reboot I get those errors在重新启动时我得到这些错误

Failed to load module "wfb" (module does not exist, 0)无法加载模块“无纺布”(模块不存在,0)
Failed to initialize GLX modul初始化失败的GLX模件
FATAL module Nvidia not found Nvidia的致命模块未找到

FATAL server error: no screen found...致命服务器错误:没有屏幕发现...

:confused: :困惑:
zoodayz zoodayz
2007-06-29, 11:43 AM CDT 2007年6月29日,日上午11:43华泽
startX does what?运行startx做什么?

I tried to relog as root and try to run nvidia-xconfig but I ended up with the same outcome as previously...我试图relog为根,尝试运行NVIDIA产品Xconfig文件,但我最终与先前相同的结果了...

on reboot I get those errors在重新启动时我得到这些错误

Failed to load module "wfb" (module does not exist, 0)无法加载模块“无纺布”(模块不存在,0)
Failed to initialize GLX modul初始化失败的GLX模件
FATAL module Nvidia not found Nvidia的致命模块未找到

FATAL server error: no screen found...致命服务器错误:没有屏幕发现...

:confused: :困惑:
zoodayz zoodayz
2007-06-29, 11:56 AM CDT 2007年6月29日,日上午11:56华泽
Ok anhow what I would do If I can get a prompt is I would startx let it shoot out a bunch of stuff that it cant start x bla bla bla then I would let it use the failsafe mode.玉anhow我会做什么,如果我能得到一个提示,我会让它运行startx拍了一堆,它cannot启动X喇嘛喇嘛喇嘛的话,我会让使用它的故障保护模式。 Let it default back to the basic drivers "if your lucky" and then if at the point I could log in I would login as root then make sure I have the proper outside repos for my Nvidia drivers then I would at prompt yumremove kmod-nvidia or however you installed the drivers "nvidia.ko" then yuminstall kmod-nvidia.让它默认回基本驱动程序“如果您的幸运”,然后,如果在这一点我可以登录我会以 root身份登录然后确定我有我的Nvidia驱动程序,我在提示yumremove kmod然后适当的回购外,NVIDIA公司然而,安装或司机“nvidia.ko”,然后yuminstall kmod - NVIDIA公司。 then change the settings after the install in the config to suit my needs and save reboot.然后更改后,在配置安装适合我的需要,并保存设置重新启动。
Seve塞弗
2007-06-29, 01:41 PM CDT 2007年6月29日,下午1时41华泽
I tried to relog as root and try to run nvidia-xconfig but I ended up with the same outcome as previously...我试图relog为根,尝试运行NVIDIA产品Xconfig文件,但我最终与先前相同的结果了...

on reboot I get those errors在重新启动时我得到这些错误

Failed to load module "wfb" (module does not exist, 0)无法加载模块“无纺布”(模块不存在,0)
Failed to initialize GLX modul初始化失败的GLX模件
FATAL module Nvidia not found Nvidia的致命模块未找到

FATAL server error: no screen found...致命服务器错误:没有屏幕发现...

:confused: :困惑:
Hello:您好:
What you need to do is你需要做的是
gedit /etc/X11/xorg.conf gedit / etc/X11/xorg.conf中
and add back :并加回:
For 64bit:对于64位:
Section "Files"部分“档案”
ModulePath "/usr/lib64/xorg/modules/extensions/nvidia" ModulePath“/ usr/lib64/xorg/modules/extensions/nvidia”
ModulePath "/usr/lib64/xorg/modules" ModulePath“/ usr/lib64/xorg/modules”
EndSection EndSection
For 32bit对于32位
Section "Files"部分“档案”
ModulePath "/usr/lib/xorg/modules/extensions/nvidia" ModulePath“/ usr / lib /的Xorg /模块/扩展/ NVIDIA公司”
ModulePath "/usr/lib/xorg/modules" ModulePath“/ usr / lib /的Xorg /模块”
EndSection EndSection
You should also add to the end of the file :您还应该添加到文件的末尾:
Section "Extensions"部分“扩展”
Option "Composite" "Enable"选择“综合”,“启用”
EndSection EndSection

Save your work, exit and保存您的工作,退出和
Ctrl Alt Backspace Ctrl键ALT键退格
to restart your X server and you should be good to go.重新启动X服务器,你应该去好。

Seve塞弗
sim39 sim39
2007-07-02, 06:27 AM CDT 2007年7月2日,上午06时27华泽
thanks to everyone that helped me...感谢大家帮我...

I finally found out that I was not booting the updated kernel, so two kernels were in grub and the video driver was used by the newest one.我终于发现,我不是更新的内核启动,因此,两个内核在grub和视频驱动程序是最新的一个使用。

booting with the right kernel helps a lot...用正确的内核引导帮助很大...


_________________


页首
 用户资料  
 
5 楼 
 文章标题 : Re: 联想Y550A-PSE Nvidia 130M GT显卡 开启3D桌面特效问题~紧急求助!!!
帖子发表于 : 2009-08-29 17:42 

注册: 2009-08-25 16:29
帖子: 7
送出感谢: 0 次
接收感谢: 0 次
嗯,应该是最新的,那天整整更新了一晚上。


页首
 用户资料  
 
6 楼 
 文章标题 : Re: 联想Y550A-PSE Nvidia 130M GT显卡 开启3D桌面特效问题~紧急求助!!!
帖子发表于 : 2009-08-29 23:29 
头像

注册: 2009-08-07 16:25
帖子: 214
地址: 广州
送出感谢: 0 次
接收感谢: 0 次
呵呵 LZ和我用同一款机子啊 :em01

我前几次装ubuntu的时候遇到过这个问题,最后一次装的时候就没问题了 :em06 也不知道是怎么回事,就是内核更新了

可以试试直接用CCSM,硬件没事的话肯定可以打开特效的


页首
 用户资料  
 
7 楼 
 文章标题 : Re: 联想Y550A-PSE Nvidia 130M GT显卡 开启3D桌面特效问题~紧急求助!!!
帖子发表于 : 2009-09-01 18:43 

注册: 2009-08-25 16:29
帖子: 7
送出感谢: 0 次
接收感谢: 0 次
黑旋疯 写道:
呵呵 LZ和我用同一款机子啊 :em01

我前几次装ubuntu的时候遇到过这个问题,最后一次装的时候就没问题了 :em06 也不知道是怎么回事,就是内核更新了

可以试试直接用CCSM,硬件没事的话肯定可以打开特效的

CCSM???这个东西怎么用阿??我是第一次用linux......
如果是内核的问题的话,应该怎么解决呢??


页首
 用户资料  
 
8 楼 
 文章标题 : Re: 联想Y550A-PSE Nvidia 130M GT显卡 开启3D桌面特效问题~紧急求助!!!
帖子发表于 : 2009-09-02 19:18 

注册: 2009-08-25 16:29
帖子: 7
送出感谢: 0 次
接收感谢: 0 次
有没有高手可以帮帮我阿。。。顶起。。。


页首
 用户资料  
 
9 楼 
 文章标题 : Re: 联想Y550A-PSE Nvidia 130M GT显卡 开启3D桌面特效问题~紧急求助!!!
帖子发表于 : 2009-09-02 19:38 
头像

注册: 2008-04-14 23:29
帖子: 2114
地址: 曾也在NB大学呆过
送出感谢: 3
接收感谢: 10
内核多少阿。

显卡驱动当初你是怎么装的。

说清楚一点会有人帮你的


页首
 用户资料  
 
10 楼 
 文章标题 : Re: 联想Y550A-PSE Nvidia 130M GT显卡 开启3D桌面特效问题~紧急求助!!!
帖子发表于 : 2011-02-24 19:02 

注册: 2011-01-24 23:46
帖子: 6
送出感谢: 0 次
接收感谢: 0 次
哇!原来这个问题这么早以前就出现了啊~LZ解决了么?~这么长一段代码怎么记得下来哇,先拍照再一个字一个字敲的么?刚刚涉足ubuntu……好恐怖…………


页首
 用户资料  
 
11 楼 
 文章标题 : Re: 联想Y550A-PSE Nvidia 130M GT显卡 开启3D桌面特效问题~紧急求助!!!
帖子发表于 : 2011-07-01 11:30 

注册: 2011-06-24 12:54
帖子: 3
送出感谢: 0 次
接收感谢: 0 次
那个翻译很不给力啊


页首
 用户资料  
 
12 楼 
 文章标题 : Re: 联想Y550A-PSE Nvidia 130M GT显卡 开启3D桌面特效问题~紧急求助!!!
帖子发表于 : 2011-07-02 22:20 

注册: 2011-01-07 13:28
帖子: 2
送出感谢: 0 次
接收感谢: 0 次
用 附加驱动 里面那个 开源的替代驱动(不是推荐那个)效果会更好,你可以试试


页首
 用户资料  
 
显示帖子 :  排序  
发表新帖 回复这个主题  [ 12 篇帖子 ] 

当前时区为 UTC + 8 小时


在线用户

正在浏览此版面的用户:没有注册用户 和 3 位游客


不能 在这个版面发表主题
不能 在这个版面回复主题
不能 在这个版面编辑帖子
不能 在这个版面删除帖子
不能 在这个版面提交附件

前往 :  
本站点为公益性站点,用于推广开源自由软件,由 DiaHosting VPSBudgetVM VPS 提供服务。
我们认为:软件应可免费取得,软件工具在各种语言环境下皆可使用,且不会有任何功能上的差异;
人们应有定制和修改软件的自由,且方式不受限制,只要他们自认为合适。

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
简体中文语系由 王笑宇 翻译