[求助]重新发:pppoe(奇怪,什么都没动就可以了)
- eexpress
- 帖子: 58428
- 注册时间: 2005-08-14 21:55
- 来自: 长沙
[求助]重新发:pppoe(奇怪,什么都没动就可以了)
dpkg:依赖关系问题使得 cedega 的配置工作不能继续:
cedega 依赖于 libasound2 (>> 1.0.9);然而:
系统里的 libasound2 的版本是 1.0.8-1.
dpkg:处理 cedega (--install)时出错:
依赖关系问题 - 仍未被配置
yongyi已经帮忙找到了libc6新的包。
pppoeconf了,pon没用。Globespan adsl modem驱动eciadsl-usermode-0.11.deb已经好了(需要libc6>= 2.3.2.ds1-21)。
ifconfig出了一个tap0网络设备。不知道在那里看。
没转rp-pppoe,否则adsl-setup,adsl-start就可以了。以前显示bring up tap0就ok了。
pppoe的pon应该也可以。
cedega 依赖于 libasound2 (>> 1.0.9);然而:
系统里的 libasound2 的版本是 1.0.8-1.
dpkg:处理 cedega (--install)时出错:
依赖关系问题 - 仍未被配置
yongyi已经帮忙找到了libc6新的包。
pppoeconf了,pon没用。Globespan adsl modem驱动eciadsl-usermode-0.11.deb已经好了(需要libc6>= 2.3.2.ds1-21)。
ifconfig出了一个tap0网络设备。不知道在那里看。
没转rp-pppoe,否则adsl-setup,adsl-start就可以了。以前显示bring up tap0就ok了。
pppoe的pon应该也可以。
上次由 eexpress 在 2005-08-21 23:08,总共编辑 3 次。
● 鸣学
-
- 帖子: 3025
- 注册时间: 2005-05-07 23:57
- 联系:
rp-pppoe:
http://www.ubuntu.org.cn/support/docume ... e/rp-pppoe
libasound2:
http://packages.debian.org/cgi-bin/sear ... lla-search
BTW:这样好累啊。你还是快点把网络连上吧。还有,既然能有条件上网,就可以自己搜索 deb 包了。
http://www.ubuntu.org.cn/support/docume ... e/rp-pppoe
libasound2:
http://packages.debian.org/cgi-bin/sear ... lla-search
BTW:这样好累啊。你还是快点把网络连上吧。还有,既然能有条件上网,就可以自己搜索 deb 包了。
独自看一看大海
总想起身边走在路上的朋友
Lenovo E290-420[Celeron-M420/256M/60G/Intel GMA950]
总想起身边走在路上的朋友
Lenovo E290-420[Celeron-M420/256M/60G/Intel GMA950]
- eexpress
- 帖子: 58428
- 注册时间: 2005-08-14 21:55
- 来自: 长沙
还是yongyi好。
libasound2 testing才1.0.9-3。可靠不。
rp-pppoe好的,应该马上就可以。辛苦了。不过,这样才可以培养感情阿。
http://packages.debian.org/的搜索不清晰。找不到。
libasound2 testing才1.0.9-3。可靠不。
rp-pppoe好的,应该马上就可以。辛苦了。不过,这样才可以培养感情阿。
http://packages.debian.org/的搜索不清晰。找不到。
上次由 eexpress 在 2005-08-17 15:11,总共编辑 1 次。
● 鸣学
- eexpress
- 帖子: 58428
- 注册时间: 2005-08-14 21:55
- 来自: 长沙
- lyreopera
- 帖子: 771
- 注册时间: 2005-05-23 13:38
- 来自: gdsz
- eexpress
- 帖子: 58428
- 注册时间: 2005-08-14 21:55
- 来自: 长沙
pppoe不会用
调制解调器。。。。
# eciadsl-start
[EciAdsl 1/5] Setting up USB support...
Preliminary USB device filesystem is OK
[EciAdsl 2/5] Uploading firmware...
GlobeSpan GS7070 USB ADSL WAN Modem compatible modem found (in 2424ms)
eciadsl-firmware: success
firmware loaded successfully
[EciAdsl 3/5] Synchronization...
OK eciadsl-synch: success
Synchronization successful
[EciAdsl 4/5] Connecting to provider...
Connection successful
[EciAdsl 5/5] Setting up route table...
Waiting for tap0...
驱动完全正常。。。
# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:723 errors:0 dropped:0 overruns:0 frame:0
TX packets:723 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:64796 (63.2 KiB) TX bytes:64796 (63.2 KiB)
tap0 Link encap:Ethernet HWaddr 00:FF:41:E8:0D:C6
inet6 addr: fe80::2ff:41ff:fee8:dc6/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:378 (378.0 b)
# pppoeconf tap0
┌─────────────┤ DSL CONNECTION FOUND ├─────────┐
│ │
│ I found an Access Concentrator on tap0. Should I setup │
│ PPPOE for this connection? │
│ │
│ <是> <否> │
│ │
└──────────────────────────────────┘
│ If you continue with this program, the configuration file │
│ /etc/ppp/peers/dsl-provider will be modified. Please make sure│
│ that you have a backup copy before saying Yes. │
│ │
│ Continue with configuration? │
└───────────────────────────────────────┘
│ The DSL connection has been triggered. You can use the │
│ "plog" command to see the status or "ifconfig ppp0" │
│ for general interface info. │
└────────────────────────────────────┘
need setup /etc/resolv.conf 修改DNS
# pon dsl-provider
Plugin rp-pppoe.so loaded.
RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
rp-pppoe.so 位于 /usr/lib/pppd/2.4.2,没有提示版本低了。
没有已经连接的提示。。。。
# plog
Aug 17 19:15:34 localhost pppd[10109]: Using interface ppp0
Aug 17 19:15:34 localhost pppd[10109]: Connect: ppp0 <--> tap0
Aug 17 19:15:34 localhost pppd[10109]: Couldn't increase MTU to 1500
Aug 17 19:15:34 localhost pppd[10109]: Couldn't increase MRU to 1500
Aug 17 19:15:34 localhost pppd[10109]: Couldn't increase MRU to 1500
Aug 17 19:15:34 localhost pppd[10109]: Remote message:
# eciadsl-start
[EciAdsl 1/5] Setting up USB support...
Preliminary USB device filesystem is OK
[EciAdsl 2/5] Uploading firmware...
GlobeSpan GS7070 USB ADSL WAN Modem compatible modem found (in 2424ms)
eciadsl-firmware: success
firmware loaded successfully
[EciAdsl 3/5] Synchronization...
OK eciadsl-synch: success
Synchronization successful
[EciAdsl 4/5] Connecting to provider...
Connection successful
[EciAdsl 5/5] Setting up route table...
Waiting for tap0...
驱动完全正常。。。
# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:723 errors:0 dropped:0 overruns:0 frame:0
TX packets:723 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:64796 (63.2 KiB) TX bytes:64796 (63.2 KiB)
tap0 Link encap:Ethernet HWaddr 00:FF:41:E8:0D:C6
inet6 addr: fe80::2ff:41ff:fee8:dc6/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:378 (378.0 b)
# pppoeconf tap0
┌─────────────┤ DSL CONNECTION FOUND ├─────────┐
│ │
│ I found an Access Concentrator on tap0. Should I setup │
│ PPPOE for this connection? │
│ │
│ <是> <否> │
│ │
└──────────────────────────────────┘
│ If you continue with this program, the configuration file │
│ /etc/ppp/peers/dsl-provider will be modified. Please make sure│
│ that you have a backup copy before saying Yes. │
│ │
│ Continue with configuration? │
└───────────────────────────────────────┘
│ The DSL connection has been triggered. You can use the │
│ "plog" command to see the status or "ifconfig ppp0" │
│ for general interface info. │
└────────────────────────────────────┘
need setup /etc/resolv.conf 修改DNS
# pon dsl-provider
Plugin rp-pppoe.so loaded.
RP-PPPoE plugin version 3.3 compiled against pppd 2.4.2
rp-pppoe.so 位于 /usr/lib/pppd/2.4.2,没有提示版本低了。
没有已经连接的提示。。。。
# plog
Aug 17 19:15:34 localhost pppd[10109]: Using interface ppp0
Aug 17 19:15:34 localhost pppd[10109]: Connect: ppp0 <--> tap0
Aug 17 19:15:34 localhost pppd[10109]: Couldn't increase MTU to 1500
Aug 17 19:15:34 localhost pppd[10109]: Couldn't increase MRU to 1500
Aug 17 19:15:34 localhost pppd[10109]: Couldn't increase MRU to 1500
Aug 17 19:15:34 localhost pppd[10109]: Remote message:
代码: 全选
: Unable to find user in database^J
Aug 17 19:15:34 localhost pppd[10109]: PAP authentication failed
Aug 17 19:15:34 localhost pppd[10109]: Couldn't increase MTU to 1500
Aug 17 19:15:34 localhost pppd[10109]: Couldn't increase MRU to 1500
Aug 17 19:15:34 localhost pppd[10109]: Connection terminated.
可能是MTU的问题????认证问题???但密码等应该没错。
below is file content of /etc/ppp/peers/dsl-provider
noipdefault
usepeerdns
defaultroute
hide-password
lcp-echo-interval 20
lcp-echo-failure 3
connect /bin/true
noauth
persist
mtu 1492
noaccomp
default-asyncmap
plugin rp-pppoe.so tap0
user "CSD1873424"
● 鸣学
-
- 帖子: 3025
- 注册时间: 2005-05-07 23:57
- 联系:
- eexpress
- 帖子: 58428
- 注册时间: 2005-08-14 21:55
- 来自: 长沙
-
- 帖子: 3025
- 注册时间: 2005-05-07 23:57
- 联系:
你是用RP-PPPoE吧?参看这个:
http://www.ubuntu.org.cn/support/docume ... term=pppoe
如果是原来的,就用sudo pppoeconf 配置一下就可以上网了。sudo pon 是链接上网,sudo poff 是断线下网。
http://www.ubuntu.org.cn/support/docume ... term=pppoe
如果是原来的,就用sudo pppoeconf 配置一下就可以上网了。sudo pon 是链接上网,sudo poff 是断线下网。
独自看一看大海
总想起身边走在路上的朋友
Lenovo E290-420[Celeron-M420/256M/60G/Intel GMA950]
总想起身边走在路上的朋友
Lenovo E290-420[Celeron-M420/256M/60G/Intel GMA950]
- yonsan
- 帖子: 887
- 注册时间: 2005-07-01 18:56
- 来自: 广州市
- eexpress
- 帖子: 58428
- 注册时间: 2005-08-14 21:55
- 来自: 长沙
这些都试过了。是要用pppoe哦,dsl-provider是ppponconf指定配置的。pon dsl-provider不行。yongyi 写了:你是用RP-PPPoE吧?参看这个:
http://www.ubuntu.org.cn/support/docume ... term=pppoe
如果是原来的,就用sudo pppoeconf 配置一下就可以上网了。sudo pon 是链接上网,sudo poff 是断线下网。
rp-pppoe的哪个在以前其他的系统用的很好,ubuntu这里没反应。好像就是哪个go-gui和go执行了都一样。提示不记得了。就是没反应。
modem的配置倒是很熟悉了。以前曾经用2个版本rpm和tar的杂交配置出tap0,现在用最新版本的deb一次就成功了。
搞不好,就要买个eth0接口的modem了,那才是失败阿。要是搞好了,我就出个经验多好。以前好像Globespan的modem很多阿。
● 鸣学
-
- 帖子: 3025
- 注册时间: 2005-05-07 23:57
- 联系:
-
- 帖子: 3025
- 注册时间: 2005-05-07 23:57
- 联系:
-
- 帖子: 3025
- 注册时间: 2005-05-07 23:57
- 联系:
找到个类似的:
poff dsl-provider
deactivate eth0 in networking gui
pon dsl-provider
my conncetion never get terminated any more.
to keep eth0 from coming up at boot edit your /etc/network/interfaces by commenting out the lines:
# This is a list of hotpluggable network interfaces.
# They will be activated automatically by the hotplug subsystem.
#mapping hotplug
# script grep
# map eth0
# The primary network interface
#iface eth0 inet dhcp
独自看一看大海
总想起身边走在路上的朋友
Lenovo E290-420[Celeron-M420/256M/60G/Intel GMA950]
总想起身边走在路上的朋友
Lenovo E290-420[Celeron-M420/256M/60G/Intel GMA950]