[wiki]BinaryDriverHowto/KeyspanDriver

[oneleaf]

How to install the non-free firmware for Keyspan USB <-> serial converters

KeyspanDriverHowto:: This Howto documents how to get a Keyspan USB-to-serial converter working with Ubuntu. Most of these devices require firmware to be downloaded to the device each time you connect it to your USB bus. The problem is that this firmware is distributed with a license too restrictive to allow Ubuntu to redistribute it.
Use a kernel.org kernel

Compile your own kernel from kernel.org source. See the KernelCompileHowto for more information on how to do this.
Patch the ubuntu kernel

This is a bit sneakier. For now, I will say that you need to download the kernel.org kernel, and copy keyspan* from drivers/usb/serial to drivers/usb/serial in the unpacked ubuntu kernel tree. Also, copy the relevant bits from Kconfig in the upstream drivers/usb/serial directory into Kconfig in the same directory under the Unbutu source tree.

Then compile it, using the KernelCompileHowto as a guide.

This is a very rushed stab at an explanation, mainly so I can get the page out there, and tidy it up later. Sorry for the mess.

https://wiki.ubuntu.com/BinaryDriverHowto/KeyspanDriver

[yang119345]

如何给Keyspan USB <->串行 传换器安装非免费固件

Keyspan驱动入门::此入门为如何让Keyspan USB-串行 转换器工作在Ubuntu而写.每次您将其联接到您的USB总线的时候,大多数此类设备需要为其下载固件.问题是此固件随着过多限制以致允许Ubuntu再分发的许可证发布.
使用kernerl.org的核心

从kernel.org的源代码编译您自己的核心.参考核心编译入门为如何编译内核获得更多信息.
为Ubuntu核心打补丁

这有点神秘.此时,您需要下载kernel.org核心,并且将keyspan*从drivers/usb/serial复制到没打包的ubuntu核心树drivers/usb/serial下.同样的, 从位于drivers/usb/serial目录上游的Kconfig复制相关比特到Unbuntu源代码树的相同目录下.

然后编译它,使用核心编译入门作为指南.

此文是非常仓促投入的产物,大概实际上我可以将页面从那里拿出来,并且以后会整理它.对此文的杂乱表示抱歉.

https://wiki.ubuntu.com/BinaryDriverHowto/KeyspanDriver

[leal]

如何为Keyspan USB<->串行转换器安装非自由固件

KeyspanDriverHowto：：本指南记述了如何使Keyspan USB<->串行转换器能够在Ubuntu上工作。在每次你把它们连接到USB总线上时，大部分此类设备都要求下载相应的固件。问题是，这种固件是以极受限的协议发布的，以致Ubuntu无法将其重新分发。

使用kernel.org上的内核

从kernel.org下载源码编译自己的内核。如何编译内核的详细信息请参看KernelCompileHowto。

给Ubuntu内核打补丁

这稍微有点诡秘。暂时可按如下所述，你需要从kernel.org下载内核，并把drivers/usb/serial下的keyspan*拷贝到未打包的Ubuntu内核源代码树的drivers/usb/serial下。此外，把drivers/usb/serial上一级目录下Kconfig中相关设置信息拷贝到Ubuntu 源码树同一目录下的Kconfig中。

然后以KernelCompileHowto作为指南，编译内核。

这是个相当草草的说明，主要是这样一来我可以先把这个页面建立起来，容日后再做整理。对这杂乱不堪表示抱歉：（

https://wiki.ubuntu.com/BinaryDriverHowto/KeyspanDriver

How to install the non-free firmware for Keyspan USB <-> serial converters

KeyspanDriverHowto:: This Howto documents how to get a Keyspan USB-to-serial converter working with Ubuntu. Most of these devices require firmware to be downloaded to the device each time you connect it to your USB bus. The problem is that this firmware is distributed with a license too restrictive to allow Ubuntu to redistribute it.
Use a kernel.org kernel

Compile your own kernel from kernel.org source. See the KernelCompileHowto for more information on how to do this.
Patch the ubuntu kernel

This is a bit sneakier. For now, I will say that you need to download the kernel.org kernel, and copy keyspan* from drivers/usb/serial to drivers/usb/serial in the unpacked ubuntu kernel tree. Also, copy the relevant bits from Kconfig in the upstream drivers/usb/serial directory into Kconfig in the same directory under the Unbutu source tree.

Then compile it, using the KernelCompileHowto as a guide.

This is a very rushed stab at an explanation, mainly so I can get the page out there, and tidy it up later. Sorry for the mess.

https://wiki.ubuntu.com/BinaryDriverHowto/KeyspanDriver

[oneleaf]

http://www.ubuntu.org.cn/support/docume ... howto_view

[yang119345]

[oneleaf]

呵呵，不要难过，还有好多没有翻译呢。

[yang119345]

leal的英文却是了得。佩服。

[millenniumdark]

http://wiki.ubuntu.org.cn/BinaryDriverH ... spanDriver