笔记本装ubuntu后不发声

[wavehorse]

我的笔记本芯片组是915GM，集成声卡
lspci后显示
0000:00:00.0 Host bridge: Intel Corp. Mobile Memory Controller Hub (rev 03)
0000:00:02.0 VGA compatible controller: Intel Corp. Mobile Graphics Controller (rev 03)
0000:00:02.1 Display controller: Intel Corp. Mobile Graphics Controller (rev 03)
0000:00:1b.0 0403: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 04)
0000:00:1c.0 PCI bridge: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 04)
0000:00:1c.1 PCI bridge: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 (rev 04)
0000:00:1c.2 PCI bridge: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 3 (rev 04)
0000:00:1d.0 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04)
0000:00:1d.1 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04)
0000:00:1d.2 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04)
0000:00:1d.3 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04)
0000:00:1d.7 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev d4)
0000:00:1f.0 ISA bridge: Intel Corp. 82801FBM (ICH6M) LPC Interface Bridge (rev 04)
0000:00:1f.1 IDE interface: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 04)
0000:00:1f.3 SMBus: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04)
0000:06:06.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03)
0000:06:07.0 CardBus bridge: Texas Instruments: Unknown device 8031
0000:06:07.2 FireWire (IEEE 1394): Texas Instruments: Unknown device 8032
0000:06:07.3 Unknown mass storage controller: Texas Instruments: Unknown device 8033
0000:06:08.0 Network controller: Intel Corp. PRO/Wireless 2200BG (rev 05)

lsmod后显示(似乎没有snd开头的项)

Module Size Used by
speedstep_lib 3940 0
proc_intf 3908 0
cpufreq_powersave 1632 0
cpufreq_userspace 4348 0
cpufreq_ondemand 6140 0
freq_table 4004 0
pcmcia 22244 2
i915 19552 1
drm 65172 2 i915
ipv6 257760 9
ipw2200 71820 0
firmware_class 9984 1 ipw2200
ieee80211 23332 1 ipw2200
ieee80211_crypt 5640 1 ieee80211
ohci1394 34596 0
yenta_socket 21344 0
pcmcia_core 57984 2 pcmcia,yenta_socket
tg3 84932 0
i2c_i801 8364 0
i2c_core 22320 1 i2c_i801
usbhid 31936 0
ehci_hcd 32708 0
uhci_hcd 32816 0
usbcore 119000 4 usbhid,ehci_hcd,uhci_hcd
pci_hotplug 33488 0
intel_agp 22140 1
agpgart 33608 3 drm,intel_agp
pcspkr 3496 0
rtc 12472 0
nls_iso8859_1 3936 4
nls_cp437 5600 4
vfat 13824 4
fat 41760 1 vfat
md 47440 0
dm_mod 59420 1
capability 4648 0
commoncap 7712 1 capability
tsdev 7520 0
evdev 9344 0
joydev 9664 0
sr_mod 17188 0
sbp2 23816 0
scsi_mod 127552 2 sr_mod,sbp2
ieee1394 108312 2 ohci1394,sbp2
psmouse 21320 0
mousedev 11288 1
parport_pc 37252 0
lp 11144 0
parport 36744 2 parport_pc,lp
ide_cd 41700 0
cdrom 40220 2 sr_mod,ide_cd
reiserfs 262960 1
ext2 66632 0
ext3 137256 0
jbd 60536 1 ext3
mbcache 8356 2 ext2,ext3
ide_generic 1312 0
ide_disk 20416 7
piix 10340 1
ide_core 129356 4 ide_cd,ide_generic,ide_disk,piix
unix 28276 740
processor 22452 0
fbcon 37504 0
font 8192 1 fbcon
bitblit 5472 1 fbcon
vesafb 6724 0
cfbcopyarea 3808 1 vesafb
cfbimgblt 2912 1 vesafb
cfbfillrect 3488 1 vesafb

另外在新立得中搜索alsa-utils，显示版本已经为最新1.0.8-lubuntu1

另外有一点要提到的，我的grub启动项里加了参数 acpi=off，如果不加这个参数，就启动不了ubuntu

有人建议我升级bios，但是我现在一时又下不到
不知道还有什么办法没？

[oneleaf]

2.6.12 的内核,加上 alsa >= 1.0.9 才支持你的声卡。
升级到breezy.

[cashlu]

不用升级内核，只是升级声卡驱动就可以了

[wavehorse]

2.6.12 的内核,加上 alsa >= 1.0.9 才支持你的声卡。
升级到breezy.

如今我已经是2.6.12的内核了，同时alsa也大于1.09了
可还是没声音，不过比5.04时多了个音量按钮出来，但不能点，一点就提示
音量控制找不到要控制的任何元素和/或设备。这意味着您可能没有安装正确的 GStreamer 插件，或者您没有配置好声卡。
同时在多媒体系统选择器中选任何一种流水线都是测试失败
另外现在lsmod后，比原来多了一些snd开头的项目
lsmod|grep snd后显示
snd_hda_intel 16704 0
snd_hda_codec 80096 1 snd_hda_intel
snd_pcm_oss 52704 0
snd_mixer_oss 19296 1 snd_pcm_oss
snd_pcm 88840 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_timer 24164 1 snd_pcm
snd 54884 6 snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 9600 1 snd
snd_page_alloc 10600 2 snd_hda_intel,snd_pcm

现在还有什么办法能让我的笔记本发出声音不？

[eexpress]

GStreamer有吗。

[yonsan]

有个命令配置声卡的, 可以试试!

代码： 全选

alsaconf

[wavehorse]

晕，竟然没有这个命令
是不什么有什么东西没装？

[oneleaf]

这样，找一张breezy的LiveCD启动,看看有没有声音，如果有，就重新安装系统，如果还没有，就需要去声卡的主站点找驱动，自己编译了。

[wavehorse]

我现在装的就是breezy啊
前几天用breezy的liveCD RC也启动过，但是中间有一步（检测硬件）过不去，也不知道为什么

[catinsnow]

如果家目录下有以前配置.asoundrc文件,重命名掉试试,
试试alsamixer,看可用不,可以的话
用aplay命令播放一个wav文件试试.

[wavehorse]

根目录和家目录下都没有.asoundrc文件
alsamixer显示如下
function snd_ctl_open failed for default: No such file or directory

[catinsnow]

应该确实没有正确加载驱动,不是gst的问题.
可以试一下

代码： 全选

sudo /etc/init.d/alsa force-reload

看有什么提示,我以前的声卡,仅仅reload两遍就可以用了.
运行dmesg看有什么有关声卡的错误提示.
同时保证以下三个包都是1.0.9以上,新力得里重装一下.
alsa-base alsa-utils libasound2
重启后还是不行的话,可以试试编译安装最新的alsa 1.0.10版,看changelog对hda支持有所改善.
http://www.alsa-project.org/
对了,也用root帐号试一下alsamixer

代码： 全选

sudo alsamixer

看是不是也同样的错误.

[wavehorse]

reload了两遍，依然没用
dmesg显示
[ 9.427108] CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000
[ 9.427117] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 9.427119] CPU: L2 cache: 2048K
[ 9.427121] CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000
[ 9.427127] Intel machine check architecture supported.
[ 9.427131] Intel machine check reporting enabled on CPU#0.
[ 9.427132] CPU: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
[ 9.427136] Enabling fast FPU save and restore... done.
[ 9.427138] Enabling unmasked SIMD FPU exception support... done.
[ 9.427142] Checking 'hlt' instruction... OK.
[ 9.431113] checking if image is initramfs... it is
[ 9.935427] Freeing initrd memory: 5505k freed
[ 10.037027] NET: Registered protocol family 16
[ 10.037290] PCI: PCI BIOS revision 2.10 entry at 0xfd7be, last bus=7
[ 10.037297] PCI: Using configuration type 1
[ 10.037301] mtrr: v2.0 (20020519)
[ 10.037614] ACPI: Subsystem revision 20050729
[ 10.037616] ACPI: Interpreter disabled.
[ 10.037619] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 10.037625] pnp: PnP ACPI: disabled
[ 10.037628] PnPBIOS: Scanning system for PnP BIOS support...
[ 10.037637] PnPBIOS: Found PnP BIOS installation structure at 0xc00f6a20
[ 10.037640] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xb1b2, dseg 0x400
[ 10.039692] PnPBIOS: 20 nodes reported by PnP BIOS; 20 recorded by driver
[ 10.039725] PCI: Probing PCI hardware
[ 10.039727] PCI: Probing PCI hardware (bus 00)
[ 10.039846] Boot video device is 0000:00:02.0
[ 10.040495] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[ 10.041246] PCI: Transparent bridge - 0000:00:1e.0
[ 10.061799] pnp: 00:00: ioport range 0x4d0-0x4d1 has been reserved
[ 10.061802] pnp: 00:00: ioport range 0x1000-0x105f has been reserved
[ 10.061805] pnp: 00:00: ioport range 0x1060-0x107f has been reserved
[ 10.061808] pnp: 00:00: ioport range 0x1180-0x11bf has been reserved
[ 10.061817] pnp: 00:0b: ioport range 0xfe00-0xfe01 has been reserved
[ 10.062188] audit: initializing netlink socket (disabled)
[ 10.062192] audit: initialized
[ 10.062262] VFS: Disk quotas dquot_6.5.1
[ 10.062277] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 10.062299] devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
[ 10.062304] devfs: boot_options: 0x0
[ 10.062327] Initializing Cryptographic API
[ 10.062432] PCI: No IRQ known for interrupt pin A of device 0000:00:1c.0. Please try using pci=biosirq.
[ 10.062438] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 10.062442] pcie_portdrv_probe->Dev[2660:8086] has invalid IRQ. Check vendor BIOS
[ 10.062491] assign_interrupt_mode Found MSI capability
[ 10.062493] Allocate Port Service[pcie00]
[ 10.062514] Allocate Port Service[pcie02]
[ 10.062554] PCI: No IRQ known for interrupt pin B of device 0000:00:1c.1. Please try using pci=biosirq.
[ 10.062559] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 10.062563] pcie_portdrv_probe->Dev[2662:8086] has invalid IRQ. Check vendor BIOS
[ 10.062610] assign_interrupt_mode Found MSI capability
[ 10.062613] Allocate Port Service[pcie00]
[ 10.062632] Allocate Port Service[pcie02]
[ 10.062672] PCI: No IRQ known for interrupt pin C of device 0000:00:1c.2. Please try using pci=biosirq.
[ 10.062677] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 10.062681] pcie_portdrv_probe->Dev[2664:8086] has invalid IRQ. Check vendor BIOS
[ 10.062745] assign_interrupt_mode Found MSI capability
[ 10.062748] Allocate Port Service[pcie00]
[ 10.062771] Allocate Port Service[pcie02]
[ 10.062796] isapnp: Scanning for PnP cards...
[ 10.415513] isapnp: No Plug & Play device found
[ 10.429224] PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
[ 10.438202] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 10.438613] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 10.438617] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[ 10.438802] ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
[ 10.441258] pnp: Device 00:11 activated.
[ 10.441374] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 10.441464] io scheduler noop registered
[ 10.441474] io scheduler anticipatory registered
[ 10.441479] io scheduler deadline registered
[ 10.441486] io scheduler cfq registered
[ 10.441756] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 10.441813] NET: Registered protocol family 2
[ 10.449995] IP: routing cache hash table of 2048 buckets, 16Kbytes
[ 10.450118] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 10.450172] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 10.450206] TCP: Hash tables configured (established 8192 bind 8192)
[ 10.450261] NET: Registered protocol family 8
[ 10.450263] NET: Registered protocol family 20
[ 10.450634] Freeing unused kernel memory: 168k freed
[ 10.461293] vga16fb: initializing
[ 10.461296] vga16fb: mapped to 0xc00a0000
[ 10.584645] Console: switching to colour frame buffer device 80x30
[ 10.584649] fb0: VGA16 VGA frame buffer device
[ 10.610505] input: AT Translated Set 2 keyboard on isa0060/serio0
[ 11.688368] Capability LSM initialized
[ 11.695514] NET: Registered protocol family 1
[ 11.707666] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 11.707675] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 11.711272] ICH6: IDE controller at PCI slot 0000:00:1f.1
[ 11.711290] ICH6: chipset revision 4
[ 11.711292] ICH6: not 100% native mode: will probe irqs later
[ 11.711301] ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio
[ 11.711311] Probing IDE interface ide0...
[ 11.974226] hda: IC25N060ATMR04-0, ATA DISK drive
[ 12.412094] PNPBIOS fault.. attempting recovery.
[ 12.412098] PnPBIOS: Warning! Your PnP BIOS caused a fatal error. Attempting to continue
[ 12.412100] PnPBIOS: You may need to reboot with the "pnpbios=off" option to operate stably
[ 12.412103] PnPBIOS: Check with your vendor for an updated BIOS
[ 12.412106] PnPBIOS: pnp_dock_thread: unexpected status 0x3a
[ 12.585014] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 12.585070] Probing IDE interface ide1...
[ 13.096745] Probing IDE interface ide2...
[ 13.607739] Probing IDE interface ide3...
[ 14.118734] Probing IDE interface ide4...
[ 14.629728] Probing IDE interface ide5...
[ 15.143204] hda: max request size: 1024KiB
[ 15.164044] hda: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100)
[ 15.164375] hda: cache flushes supported
[ 15.164420] /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >
[ 15.398299] Attempting manual resume
[ 15.400373] swsusp: Suspend partition has wrong signature?
[ 15.469870] usbcore: registered new driver usbfs
[ 15.469893] usbcore: registered new driver hub
[ 15.470547] USB Universal Host Controller Interface driver v2.2
[ 15.470598] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 15.470602] uhci_hcd 0000:00:1d.0: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
[ 15.532065] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 15.532073] uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001820
[ 15.532163] hub 1-0:1.0: USB hub found
[ 15.532168] hub 1-0:1.0: 2 ports detected
[ 15.534962] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 15.534966] uhci_hcd 0000:00:1d.1: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
[ 15.596844] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 15.596849] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001840
[ 15.596927] hub 2-0:1.0: USB hub found
[ 15.596931] hub 2-0:1.0: 2 ports detected
[ 15.599835] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 15.599839] uhci_hcd 0000:00:1d.2: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
[ 15.661721] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 15.661726] uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001860
[ 15.661802] hub 3-0:1.0: USB hub found
[ 15.661807] hub 3-0:1.0: 2 ports detected
[ 15.664706] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 15.664710] uhci_hcd 0000:00:1d.3: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
[ 15.726589] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 15.726595] uhci_hcd 0000:00:1d.3: irq 10, io base 0x00001880
[ 15.726675] hub 4-0:1.0: USB hub found
[ 15.726679] hub 4-0:1.0: 2 ports detected
[ 15.756488] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 15.756493] ehci_hcd 0000:00:1d.7: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
[ 15.756522] ehci_hcd 0000:00:1d.7: debug port 1
[ 15.756556] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 15.756562] ehci_hcd 0000:00:1d.7: irq 11, io mem 0xb0040000
[ 15.760449] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 15.760456] ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
[ 15.760534] hub 5-0:1.0: USB hub found
[ 15.760539] hub 5-0:1.0: 8 ports detected
[ 15.766492] usb 2-1: new low speed USB device using uhci_hcd and address 2
[ 15.813052] tg3.c:v3.31 (June 8, 2005)
[ 15.865656] eth0: Tigon3 [partno(BCM95705A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:c0:9f:9c:18:8b
[ 15.865662] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
[ 15.865665] eth0: dma_rwctrl[763f0000]
[ 16.185667] usb 2-1: new low speed USB device using uhci_hcd and address 3
[ 17.907152] usbcore: registered new driver hiddev
[ 17.924760] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.1-1
[ 17.924765] usbcore: registered new driver usbhid
[ 17.924768] drivers/usb/input/hid-core.c: v2.01:USB HID core driver
[ 18.453895] Attempting manual resume
[ 18.464688] swsusp: Suspend partition has wrong signature?
[ 18.505653] ReiserFS: hda8: found reiserfs format "3.6" with standard journal
[ 19.361642] ReiserFS: hda8: using ordered data mode
[ 19.385646] ReiserFS: hda8: journal params: device hda8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 19.385986] ReiserFS: hda8: checking transaction log (hda8)
[ 19.443766] ReiserFS: hda8: Using r5 hash to sort names
[ 20.615036] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 23.048890] Adding 819272k swap on /dev/hda9. Priority:-1 extents:1
[ 33.565718] PnPBIOS: get_dev_node: function not supported on this system
[ 33.565723] pnp: Failed to activate device 00:15.
[ 33.565726] parport_pc: probe of 00:15 failed with error -5
[ 33.571267] lp: driver loaded but no devices found
[ 33.586118] mice: PS/2 mouse device common for all mice
[ 33.601876] ieee1394: Initialized config rom entry `ip1394'
[ 33.606765] SCSI subsystem initialized
[ 33.611118] sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
[ 34.181703] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x81a0b1, caps: 0xa04713/0x204000
[ 34.183588] input: SynPS/2 Synaptics TouchPad on isa0060/serio1
[ 34.360142] ts: Compaq touchscreen protocol output
[ 37.452547] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[ 39.071644] kjournald starting. Commit interval 5 seconds
[ 39.071825] EXT3 FS on hda7, internal journal
[ 39.071828] EXT3-fs: mounted filesystem with ordered data mode.
[ 40.088925] Linux agpgart interface v0.101 (c) Dave Jones
[ 40.094221] agpgart: Detected an Intel 915GM Chipset.
[ 40.095070] agpgart: Detected 7932K stolen memory.
[ 40.121959] agpgart: AGP aperture is 256M @ 0xc0000000
[ 40.299036] PCI: No IRQ known for interrupt pin A of device 0000:00:1b.0. Please try using pci=biosirq.
[ 40.299050] hda-intel: unable to grab IRQ 0
[ 40.299060] HDA Intel: probe of 0000:00:1b.0 failed with error -16
[ 40.473055] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 40.476335] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 40.536812] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 40.597873] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 40.823041] hw_random: cannot enable RNG, aborting
[ 41.028822] Linux Kernel Card Services
[ 41.028825] options: [pci] [cardbus] [pm]
[ 41.036913] Yenta: CardBus bridge found at 0000:06:07.0 [1025:0067]
[ 41.036962] Yenta: Enabling burst memory read transactions
[ 41.036968] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 41.036970] Yenta: Routing CardBus interrupts to PCI
[ 41.036976] Yenta TI: socket 0000:06:07.0, mfunc 0x01c21b22, devctl 0x64
[ 41.257939] Yenta: ISA IRQ mask 0x02f8, PCI irq 11
[ 41.257943] Socket status: 30000006
[ 41.317261] ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
[ 41.369573] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[b0117000-b01177ff] Max Packet=[2048]
[ 41.461952] ieee80211_crypt: registered algorithm 'NULL'
[ 41.464937] ieee80211: 802.11 data/management/control stack, 1.0.3
[ 41.464940] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 41.471599] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.6
[ 41.471602] ipw2200: Copyright(c) 2003-2004 Intel Corporation
[ 41.473918] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 42.309486] ipw2200: Radio Frequency Kill Switch is On:
[ 42.309488] Kill switch must be turned off for wireless networking to work.
[ 42.623762] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f0000520e0a]
[ 43.898003] Real Time Clock Driver v1.12
[ 43.949496] input: PC Speaker
[ 47.244901] tg3: eth0: Link is up at 10 Mbps, half duplex.
[ 47.244905] tg3: eth0: Flow control is off for TX and off for RX.
[ 47.526737] NET: Registered protocol family 10
[ 47.526833] Disabled Privacy Extensions on device c031eb40(lo)
[ 47.526951] IPv6 over IPv4 tunneling driver
[ 58.108552] [drm] Initialized drm 1.0.0 20040925
[ 58.115094] [drm] Initialized i915 1.2.0 20040405 on minor 0: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller
[ 58.115599] mtrr: base(0xc0020000) is not aligned on a size(0x600000) boundary
[ 58.214047] eth0: no IPv6 routers present
[ 61.972794] apm: BIOS not found.
[ 63.445822] cs: IO port probe 0x100-0x4ff: clean.
[ 63.448358] cs: IO port probe 0xc00-0xcf7: clean.
[ 63.449044] cs: IO port probe 0xa00-0xaff: clean.
[ 65.044756] Bluetooth: Core ver 2.7
[ 65.044765] NET: Registered protocol family 31
[ 65.044766] Bluetooth: HCI device and connection manager initialized
[ 65.044775] Bluetooth: HCI socket layer initialized
[ 65.124905] Bluetooth: L2CAP ver 2.7
[ 65.124909] Bluetooth: L2CAP socket layer initialized
[ 65.159486] Bluetooth: RFCOMM ver 1.5
[ 65.159495] Bluetooth: RFCOMM socket layer initialized
[ 65.159502] Bluetooth: RFCOMM TTY layer initialized
[ 293.935037] PCI: No IRQ known for interrupt pin A of device 0000:00:1b.0. Please try using pci=biosirq.
[ 293.935054] hda-intel: unable to grab IRQ 0
[ 293.935083] HDA Intel: probe of 0000:00:1b.0 failed with error -16
[ 534.297854] PCI: No IRQ known for interrupt pin A of device 0000:00:1b.0. Please try using pci=biosirq.
[ 534.297875] hda-intel: unable to grab IRQ 0
[ 534.297889] HDA Intel: probe of 0000:00:1b.0 failed with error -16

我找不到其中哪些是有关声卡的，就都列出来了

我的那三个有关alsa的包都是最新版的1.09以上
另外要提到的是，我禁用了acpi，就是在grub的启动行里加上了acpi=off的参数
因为不加这个参数，我的ubuntu就启动不起来，直接停在booting the kernel了

[jczuo]

还是因为ACPI的问题，要修改一下内核，重新编译，就没问题了。

参考viewtopic.php?t=6508&highlight=

[odysseus]

我的声卡也是intel high definition audio ，必须把BIOS里的板载声卡关掉，不然不能起动，死在starting hotplug subsystem ,各位高手怎办