[ 0.000000] Total memory = 320MB; using 1024kB for hash table (at cff00000)
[ 0.000000] Linux version 2.6.15-52-powerpc (buildd@royal) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 Fri Jul 11 13:22:30 UTC 2008
[ 0.000000] Found initrd at 0xc1900000:0xc20aa000
[ 0.000000] Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0xc0
[ 0.000000] Mapped at 0xfdfc0000
[ 0.000000] Found a Pangea mac-io controller, rev: 0, mapped at 0xfdf40000
[ 0.000000] Processor NAP mode on idle enabled.
[ 0.000000] PowerMac motherboard: iBook FireWire
[ 0.000000] Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0
[ 0.000000] Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0
[ 0.000000] Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0
[ 0.000000] via-pmu: Server Mode is disabled
[ 0.000000] PMU driver 2 initialized for Core99, firmware: 0c
[ 0.000000] nvram: Checking bank 0...
[ 0.000000] nvram: gen0=2335, gen1=2336
[ 0.000000] nvram: Active bank is: 1
[ 0.000000] nvram: OF partition at 0x210
[ 0.000000] nvram: XP partition at 0x1a30
[ 0.000000] nvram: NR partition at 0x1b30
[ 0.000000] Top of RAM: 0x14000000, Total RAM: 0x14000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] On node 0 totalpages: 81920
[ 0.000000] DMA zone: 81920 pages, LIFO batch:15
[ 0.000000] DMA32 zone: 0 pages, LIFO batch:0
[ 0.000000] Normal zone: 0 pages, LIFO batch:0
[ 0.000000] HighMem zone: 0 pages, LIFO batch:0
[ 0.000000] Built 1 zonelists
[ 0.000000] Kernel command line: root=/dev/hda3 ro quiet splash
[ 0.000000] mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs
[ 0.000000] mpic: ISU size: 64, shift: 6, mask: 3f
[ 0.000000] mpic: Initializing for 64 sources
[ 0.000000] PID hash table entries: 2048 (order: 11, 32768 bytes)
[ 0.000000] GMT Delta read from XPRAM: 480 minutes, DST: off
[ 0.000000] time_init: decrementer frequency = 16.640000 MHz
[ 0.000000] time_init: processor frequency = 499.999995 MHz
[ 29.184903] Console: colour dummy device 80x25
[ 29.187357] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 29.189348] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 29.237078] High memory: 0k
[ 29.237096] Memory: 311928k/327680k available (2692k kernel code, 15448k reserved, 276k data, 304k bss, 180k init)
[ 29.237438] Calibrating delay loop... 33.15 BogoMIPS (lpj=66304)
[ 29.320596] Security Framework v1.0.0 initialized
[ 29.320647] SELinux: Disabled at boot.
[ 29.320707] Mount-cache hash table entries: 512
[ 29.321320] device-tree: property "l2-cache" name conflicts with node in /cpus/PowerPC,750@0
[ 29.324084] checking if image is initramfs... it is
[ 31.303281] Freeing initrd memory: 7848k freed
[ 31.306694] NET: Registered protocol family 16
[ 31.307818] PCI: Probing PCI hardware
[ 31.316152] Registering PowerMac CPU frequency driver
[ 31.316179] Low: 400 Mhz, High: 499 Mhz, Boot: 499 Mhz
[ 31.316407] Thermal assist unit using timers, shrink_timer: 500 jiffies
[ 31.318367] audit: initializing netlink socket (disabled)
[ 31.318429] audit(1219512084.128:1): initialized
[ 31.318929] VFS: Disk quotas dquot_6.5.1
[ 31.319039] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 31.319325] Initializing Cryptographic API
[ 31.319346] io scheduler noop registered
[ 31.319378] io scheduler anticipatory registered
[ 31.319398] io scheduler deadline registered
[ 31.319448] io scheduler cfq registered
[ 31.320288] PCI: Enabling device 0000:00:10.0 (0086 -> 0087)
[ 31.320932] aty128fb: Invalid ROM signature 638e should be 0xaa55
[ 31.320959] aty128fb: BIOS not located, guessing timings.
[ 31.320983] aty128fb: Rage128 LF M3 AGP [chip rev 0x0] 8M 128-bit SDR SGRAM (1:1)
[ 31.355270] Console: switching to colour frame buffer device 128x48
[ 31.365067] Registered "ati" backlight controller,level: 15/15
[ 31.365087] fb0: ATY Rage128 frame buffer device on Rage128 LF M3 AGP
[ 31.451746] Macintosh non-volatile memory driver v1.1
[ 31.452058] IN from bad port 64 at c018d6e8
[ 31.452122] IN from bad port 60 at c018d71c
[ 31.452132] IN from bad port 64 at c018d6e8
[ 31.452189] IN from bad port 60 at c018d71c
[ 31.452199] IN from bad port 64 at c018d6e8
[ 31.452256] IN from bad port 60 at c018d71c
[ 31.452265] IN from bad port 64 at c018d6e8
[ 31.452323] IN from bad port 60 at c018d71c
[ 31.452333] IN from bad port 64 at c018d6e8
[ 31.452390] IN from bad port 60 at c018d71c
[ 31.452400] IN from bad port 64 at c018d6e8
[ 31.452457] IN from bad port 60 at c018d71c
[ 31.452467] IN from bad port 64 at c018d6e8
[ 31.452524] IN from bad port 60 at c018d71c
[ 31.452534] IN from bad port 64 at c018d6e8
[ 31.452592] IN from bad port 60 at c018d71c
[ 31.452601] IN from bad port 64 at c018d6e8
[ 31.452659] IN from bad port 60 at c018d71c
[ 31.452668] IN from bad port 64 at c018d6e8
[ 31.452726] IN from bad port 60 at c018d71c
[ 31.452735] IN from bad port 64 at c018d6e8
[ 31.452793] IN from bad port 60 at c018d71c
[ 31.452802] IN from bad port 64 at c018d6e8
[ 31.452860] IN from bad port 60 at c018d71c
[ 31.452869] IN from bad port 64 at c018d6e8
[ 31.452927] IN from bad port 60 at c018d71c
[ 31.452936] IN from bad port 64 at c018d6e8
[ 31.452994] IN from bad port 60 at c018d71c
[ 31.453003] IN from bad port 64 at c018d6e8
[ 31.453061] IN from bad port 60 at c018d71c
[ 31.453070] IN from bad port 64 at c018d6e8
[ 31.453128] IN from bad port 60 at c018d71c
[ 31.453137] IN from bad port 64 at c018d6e8
[ 31.453169] i8042.c: No controller found.
[ 31.454960] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 31.455406] MacIO PCI driver attached to Pangea chipset
[ 31.458170] input: Macintosh mouse button emulation as /class/input/input0
[ 31.458725] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 31.458750] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 31.458806] adb: starting probe task...
[ 31.485133] adb devices: [2]: 2 c9 [7]: 7 1f
[ 31.490642] ADB keyboard at 2, handler 1
[ 31.490688] Detected ADB keyboard, type JIS.
[ 31.490909] input: ADB keyboard as /class/input/input1
[ 31.491145] input: ADB Powerbook buttons as /class/input/input2
[ 31.491166] adb: finished probe task...
[ 32.480489] ide0: Found Apple KeyLargo ATA-4 controller, bus ID 2, irq 19
[ 32.480554] Probing IDE interface ide0...
[ 32.768823] hda: TOSHIBA MK1017GAP, ATA DISK drive
[ 33.216806] hdb: MATSHITA CR-176, ATAPI CD/DVD-ROM drive
[ 33.272501] hda: Enabling Ultra DMA 2
[ 33.273507] hdb: Enabling Ultra DMA 2
[ 33.274634] ide0 at 0xd500e000-0xd500e007,0xd500e160 on irq 19
[ 33.275460] mice: PS/2 mouse device common for all mice
[ 33.275790] NET: Registered protocol family 2
[ 33.308748] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 33.309532] TCP established hash table entries: 16384 (order: 4, 65536 bytes)
[ 33.310150] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 33.310700] TCP: Hash tables configured (established 16384 bind 16384)
[ 33.310714] TCP reno registered
[ 33.311025] TCP bic registered
[ 33.311052] NET: Registered protocol family 1
[ 33.311086] NET: Registered protocol family 8
[ 33.311095] NET: Registered protocol family 20
[ 33.311325] Freeing unused kernel memory: 180k init
[ 34.911747] Capability LSM initialized
[ 35.066289] Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits
[ 35.066700] Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
[ 37.652409] hda: max request size: 128KiB
[ 38.017883] hda: 19640880 sectors (10056 MB), CHS=19485/16/63, UDMA(33)
[ 38.017921] hda: cache flushes not supported
[ 38.018761] hda: [mac] hda1 hda2 hda3 hda4
[ 38.181573] hdb: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
[ 38.181625] Uniform CD-ROM driver Revision: 3.20
[ 39.095994] usbcore: registered new driver usbfs
[ 39.098061] usbcore: registered new driver hub
[ 39.106421] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[ 39.108373] PCI: Enabling device 0001:10:18.0 (0000 -> 0002)
[ 39.108438] ohci_hcd 0001:10:18.0: OHCI Host Controller
[ 39.110720] ohci_hcd 0001:10:18.0: new USB bus registered, assigned bus number 1
[ 39.110773] ohci_hcd 0001:10:18.0: irq 27, io mem 0x80081000
[ 39.145549] hub 1-0:1.0: USB hub found
[ 39.145639] hub 1-0:1.0: 2 ports detected
[ 39.249838] PCI: Enabling device 0001:10:19.0 (0000 -> 0002)
[ 39.249903] ohci_hcd 0001:10:19.0: OHCI Host Controller
[ 39.250470] ohci_hcd 0001:10:19.0: new USB bus registered, assigned bus number 2
[ 39.250520] ohci_hcd 0001:10:19.0: irq 28, io mem 0x80080000
[ 39.713537] hub 2-0:1.0: USB hub found
[ 39.713632] hub 2-0:1.0: 2 ports detected
[ 39.935799] ieee1394: Initialized config rom entry `ip1394'
[ 39.950567] ohci1394: $Rev: 1313 $ Ben Collins <
bcollins@debian.org>
[ 39.953837] ohci1394: fw-host0: Unexpected PCI resource length of 1000!
[ 40.002570] usb 2-1: new low speed USB device using ohci_hcd and address 2
[ 40.004413] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048]
[ 40.267666] usbcore: registered new driver hiddev
[ 40.279540] input: HID 062a:0000 as /class/input/input3
[ 40.280051] input: USB HID v1.10 Mouse [HID 062a:0000] on usb-0001:10:19.0-1
[ 40.280113] usbcore: registered new driver usbhid
[ 40.280127] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 40.424857] Attempting manual resume
[ 40.583502] kjournald starting. Commit interval 5 seconds
[ 40.583578] EXT3-fs: mounted filesystem with ordered data mode.
[ 58.574359] ts: Compaq touchscreen protocol output
[ 86.420806] Linux agpgart interface v0.101 (c) Dave Jones
[ 86.426169] agpgart: Detected Apple UniNorth/Pangea chipset
[ 86.426553] agpgart: configuring for size idx: 4
[ 86.426843] agpgart: AGP aperture is 16M @ 0x0
[ 88.304599] sungem.c:v0.98 8/24/03 David S. Miller (
davem@redhat.com)
[ 88.368840] PHY ID: 4061e3, addr: 0
[ 88.370548] eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:03:93:14:ed:dc
[ 88.370576] eth0: Found BCM5221 PHY
[ 90.768685] eth0: Link is up at 100 Mbps, full-duplex.
[ 90.768713] eth0: Pause is disabled
[ 91.753549] NET: Registered protocol family 17
[ 92.785053] apm_emu: APM Emulation 0.5 initialized.
[ 93.131019] SCSI subsystem initialized
[ 93.160151] sbp2: $Rev: 1306 $ Ben Collins <
bcollins@debian.org>
[ 93.160184] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[ 93.160194] ieee1394: sbp2: Try serialize_io=0 for better performance
[ 94.900912] input: PowerMac Beep as /class/input/input4
[ 95.499981] fuse init (API version 7.3)
[ 96.009517] Adding 437584k swap on /dev/hda4. Priority:-1 extents:1 across:437584k
[ 96.128707] EXT3 FS on hda3, internal journal
[ 97.486528] device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
dm-devel@redhat.com
[ 117.934328] eth0: Link is up at 100 Mbps, full-duplex.
[ 117.934367] eth0: Pause is disabled
[ 182.690363] NET: Registered protocol family 10
[ 182.690894] lo: Disabled Privacy Extensions
[ 182.691655] IPv6 over IPv4 tunneling driver
[ 289.331489] eth0: Link is up at 100 Mbps, full-duplex.
[ 289.331531] eth0: Pause is disabled
[ 339.251977] eth0: Link is up at 100 Mbps, full-duplex.
[ 339.252012] eth0: Pause is disabled
[ 1953.362446] eth0: Link down
[ 1955.762518] eth0: Link is up at 100 Mbps, full-duplex.
[ 1955.762550] eth0: Pause is disabled
[ 1988.167112] eth0: Link down
[ 1990.567225] eth0: Link is up at 100 Mbps, full-duplex.
[ 1990.567259] eth0: Pause is disabled
[ 4167.015636] failed to set volume
[ 4167.819026] eth0: suspending, WakeOnLan disabled
[ 4167.912915] aty128fb: suspending...
[ 4168.572759] aty128fb: resumed !
[ 4168.725299] eth0: resuming
[ 4168.790656] PHY ID: 4061e3, addr: 0
[ 4171.190461] eth0: Link is up at 100 Mbps, full-duplex.
[ 4171.190697] eth0: Pause is disabled
[ 4171.229740] hda: Enabling Ultra DMA 2
[ 4171.281298] hdb: Enabling Ultra DMA 2
[ 4172.067654] adb: starting probe task...
[ 4172.092346] adb devices: [2]: 2 c9 [7]: 7 1f
[ 4172.097378] ADB keyboard at 2, handler 1
[ 4172.097590] adb: finished probe task...
[ 4185.174386] failed to set volume
[ 4185.855047] eth0: suspending, WakeOnLan disabled
[ 4185.950834] aty128fb: suspending...
[ 4186.610193] aty128fb: resumed !
[ 4186.763557] eth0: resuming
[ 4186.828925] PHY ID: 4061e3, addr: 0
[ 4189.228719] eth0: Link is up at 100 Mbps, full-duplex.
[ 4189.228973] eth0: Pause is disabled
[ 4189.240153] hda: Enabling Ultra DMA 2
[ 4189.251569] hdb: Enabling Ultra DMA 2
[ 4190.037851] adb: starting probe task...
[ 4190.065447] adb devices: [2]: 2 c9 [7]: 7 1f
[ 4190.070994] ADB keyboard at 2, handler 1
[ 4190.071176] adb: finished probe task...
[ 4201.638248] failed to set volume
[ 4202.279489] eth0: suspending, WakeOnLan disabled
[ 4202.372636] aty128fb: suspending...
[ 4203.029868] aty128fb: resumed !
[ 4203.182427] eth0: resuming
[ 4203.247809] PHY ID: 4061e3, addr: 0
[ 4205.580022] hda: Enabling Ultra DMA 2
[ 4205.587849] hdb: Enabling Ultra DMA 2
[ 4205.647596] eth0: Link is up at 100 Mbps, full-duplex.
[ 4205.647852] eth0: Pause is disabled
[ 4206.372731] adb: starting probe task...
[ 4206.399709] adb devices: [2]: 2 c9 [7]: 7 1f
[ 4206.405293] ADB keyboard at 2, handler 1
[ 4206.405473] adb: finished probe task...
[ 5218.577116] usb 1-1: new full speed USB device using ohci_hcd and address 2
[ 5221.753175] usb 1-1: device descriptor read/64, error -110
[ 5237.035311] usb 1-1: device descriptor read/64, error -110
[ 5237.315293] usb 1-1: new full speed USB device using ohci_hcd and address 3
[ 5240.494786] usb 1-1: device descriptor read/64, error -110
[ 5255.779270] usb 1-1: device descriptor read/64, error -110
[ 5256.059235] usb 1-1: new full speed USB device using ohci_hcd and address 4
[ 5266.467296] usb 1-1: device not accepting address 4, error -110
[ 5266.643298] usb 1-1: new full speed USB device using ohci_hcd and address 5
[ 5277.054550] usb 1-1: device not accepting address 5, error -110
[ 5411.370557] usb 1-1: new full speed USB device using ohci_hcd and address 6
[ 5414.546566] usb 1-1: device descriptor read/64, error -110
[ 5429.826583] usb 1-1: device descriptor read/64, error -110
[ 5430.106596] usb 1-1: new full speed USB device using ohci_hcd and address 7
[ 5433.282588] usb 1-1: device descriptor read/64, error -110
[ 5448.562555] usb 1-1: device descriptor read/64, error -110
[ 5448.842546] usb 1-1: new full speed USB device using ohci_hcd and address 8
[ 5459.250556] usb 1-1: device not accepting address 8, error -110
[ 5459.426566] usb 1-1: new full speed USB device using ohci_hcd and address 9
[ 5469.834560] usb 1-1: device not accepting address 9, error -110
[ 6872.360996] usb 1-1: new full speed USB device using ohci_hcd and address 10
[ 6875.536944] usb 1-1: device descriptor read/64, error -110
[ 6890.817930] usb 1-1: device descriptor read/64, error -110
[ 6891.097929] usb 1-1: new full speed USB device using ohci_hcd and address 11
[ 6894.273909] usb 1-1: device descriptor read/64, error -110
[ 6908.284956] usb 1-1: new full speed USB device using ohci_hcd and address 12
[ 6911.460931] usb 1-1: device descriptor read/64, error -110
[ 6926.740918] usb 1-1: device descriptor read/64, error -110
[ 6927.020921] usb 1-1: new full speed USB device using ohci_hcd and address 13
[ 6930.196960] usb 1-1: device descriptor read/64, error -110
[ 6945.476896] usb 1-1: device descriptor read/64, error -110
[ 6945.756925] usb 1-1: new full speed USB device using ohci_hcd and address 14
[ 6956.164907] usb 1-1: device not accepting address 14, error -110
[ 6956.340918] usb 1-1: new full speed USB device using ohci_hcd and address 15
[ 6966.753073] usb 1-1: device not accepting address 15, error -110
[ 8123.004508] hdb: packet command error: status=0x51 { DriveReady SeekComplete Error }
[ 8123.004548] hdb: packet command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
[ 8123.004567] ide: failed opcode was: unknown
[ 8123.006809] cdrom: open failed.
[ 8392.802606] usb 1-1: new full speed USB device using ohci_hcd and address 16
[ 8395.979492] usb 1-1: device descriptor read/64, error -110
[ 8397.895508] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 8399.087505] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 8400.279506] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 8401.471523] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 8402.383514] usb 1-1: new full speed USB device using ohci_hcd and address 20
[ 8405.559496] usb 1-1: device descriptor read/64, error -110
[ 8420.839504] usb 1-1: device descriptor read/64, error -110
[ 8421.119497] usb 1-1: new full speed USB device using ohci_hcd and address 21
[ 8424.295661] usb 1-1: device descriptor read/64, error -110
[ 8426.008319] hdb: packet command error: status=0x51 { DriveReady SeekComplete Error }
[ 8426.008362] hdb: packet command error: error=0x54 { AbortedCommand LastFailedSense=0x05 }
[ 8426.008381] ide: failed opcode was: unknown
[ 8426.010706] cdrom: open failed.
[ 8439.575510] usb 1-1: device descriptor read/64, error -110
[ 8439.855470] usb 1-1: new full speed USB device using ohci_hcd and address 22
[ 8450.263470] usb 1-1: device not accepting address 22, error -110
[ 8450.439516] usb 1-1: new full speed USB device using ohci_hcd and address 23
[ 8460.847474] usb 1-1: device not accepting address 23, error -110
[ 9358.317128] usb 1-1: new full speed USB device using ohci_hcd and address 24
[ 9361.493181] usb 1-1: device descriptor read/64, error -110
[ 9376.778015] usb 1-1: device descriptor read/64, error -110
[ 9377.058019] usb 1-1: new full speed USB device using ohci_hcd and address 25
[ 9380.234090] usb 1-1: device descriptor read/64, error -110
