配置了3D桌面后重启。。。死机。。。。然后强行关机。。
现在开机不能进去x
ubuntu 不能启动x
版面规则
我们都知道新人的确很菜,也喜欢抱怨,并且带有浓厚的Windows习惯,但既然在这里询问,我们就应该有责任帮助他们解决问题,而不是直接泼冷水、简单的否定或发表对解决问题没有任何帮助的帖子。乐于分享,以人为本,这正是Ubuntu的精神所在。
我们都知道新人的确很菜,也喜欢抱怨,并且带有浓厚的Windows习惯,但既然在这里询问,我们就应该有责任帮助他们解决问题,而不是直接泼冷水、简单的否定或发表对解决问题没有任何帮助的帖子。乐于分享,以人为本,这正是Ubuntu的精神所在。
-
- 帖子: 7
- 注册时间: 2008-09-03 9:55
- dsj
- 帖子: 810
- 注册时间: 2008-08-21 20:26
-
- 帖子: 18311
- 注册时间: 2008-01-09 22:41
- dsj
- 帖子: 810
- 注册时间: 2008-08-21 20:26
-
- 帖子: 7
- 注册时间: 2008-09-03 9:55
-
- 帖子: 7
- 注册时间: 2008-09-03 9:55
-
- 帖子: 7
- 注册时间: 2008-09-03 9:55
- C.MyDogs
- 帖子: 284
- 注册时间: 2008-08-01 16:03
- 来自: 宁波
You can install 915resolution and vbetool the same way you install any software in ubuntu. Either click on System > Administration > Synaptic Package manager, or open a terminal and run sudo aptitude install 915resolution vbetool
To make 915resolution available you may need to enable the universe repository, either through Synaptic Package Manager > Settings > Repositories or by editing /etc/apt/sources.list. If you had to enable the universe repository you'll need to update the list of packages by clicking reload in Synaptic or running sudo aptitude update
915resolution should automatically start at boot. You can start it now by running sudo /etc/init.d/915resolution start then restarting Xorg by logging out and pressing Ctrl+Alt+Backspace. This should start you up in the new resolution as long as it is listed in your /etc/X11/xorg.conf file. If it doesn't work, try rebooting, if still nothing then post the output of sudo 915resolution -l and the contents of /etc/X11/xorg.conf
EDIT: I now see the HOWTO you are refering too. Frankly, this is news to me (and possibly good news!) I'll test it out tomorrow night....
找了这些,楼主E文应该比我好,看看吧。
意思:
是可以安装915的驱动,恢复后再安装新的。
To make 915resolution available you may need to enable the universe repository, either through Synaptic Package Manager > Settings > Repositories or by editing /etc/apt/sources.list. If you had to enable the universe repository you'll need to update the list of packages by clicking reload in Synaptic or running sudo aptitude update
915resolution should automatically start at boot. You can start it now by running sudo /etc/init.d/915resolution start then restarting Xorg by logging out and pressing Ctrl+Alt+Backspace. This should start you up in the new resolution as long as it is listed in your /etc/X11/xorg.conf file. If it doesn't work, try rebooting, if still nothing then post the output of sudo 915resolution -l and the contents of /etc/X11/xorg.conf
EDIT: I now see the HOWTO you are refering too. Frankly, this is news to me (and possibly good news!) I'll test it out tomorrow night....
找了这些,楼主E文应该比我好,看看吧。
意思:
是可以安装915的驱动,恢复后再安装新的。
T400S ,SP9400, 64G SSD+500G HDD, 2G+4G ROM,1440*900 LED, GOBI1000 WWAN